This paper analyzes a piled-raft foundation on non-homogeneous soils with variable layer depth percentages. The present work aims to perform a three-dimensional finite element analysis of a piled-raft foundation subjected to vertical load using the PLAXIS 3D software. Parametric analysis was carried out to determine the effect of soil type and initial layer thickness. The parametric study showed that increasing the relative density from 30 % to 80 % of the upper sand layer and the thickness of the first layer has led to an increase in the ultimate load and a decrease in the settlement of piled raft foundations for the cases of sand over weak soil.  In clay over weak soil, the ultimate load of the piled raft foundation w

Generally, direct measurement of soil compression index (Cc) is expensive and time-consuming. To save time and effort, indirect methods to obtain Cc may be an inexpensive option. Usually, the indirect methods are based on a correlation between some easier measuring descriptive variables such as liquid limit, soil density, and natural water content. This study used the ANFIS and regression methods to obtain Cc indirectly. To achieve the aim of this investigation, 177 undisturbed samples were collected from the cohesive soil in Sulaymaniyah Governorate in Iraq. Results of this study indicated that ANFIS models over-performed the Regression method in estimating Cc with R² of 0.66 and 0.48 for both ANFIS and Regre

The research aims to identify the role of strategic improvisation as an independent variable with its dimensions (Building the Solution, Intuition, Adaptation, and Spontaneity) and the Entrepreneurial Orientation as a dependent variable with its dimensions (Identifying Opportunities, Creativity, Adopting risk, and Vision). This research has been applied in the Rafidain Bank and its branches (Sunk, People, Al-Firdaws, and Alawiya); it used the questionnaire as a basic tool for collecting information. The sample was intentionality, which included all the heads of departments in the bank’s branches, which amounted to (33) workers, and data on the questionnaire paragraphs of 28 were processed using the SPSS V.23 and AMOS V.23). The most impor

Fumonisin B1 is toxic secondary metabolites compound produced by Fusarium spp. on maize and maize products causes health problems to human and animal. Therefore, this research is planned to study the effect of FB1 on the expression of TLR-2 & 4 in liver and kidney cells of mice. Four group of male mice were orally administrated with single dose of FB1 toxin as the following: 0 ppb, 800 ppb, 1200 ppb and 1600 ppb. After two weeks all animals were sacrificed, liver and kidney autopsies were taken and the level of TLR-2 & 4 detected in each four group by immunohistochemistry technique (IHC). According to the IHC examination of groups (1, 2, 3 and 4) strong expression of TLR2 in liver and kidney were (0%, 33.3%, 100%, 100%), respectively. This

This research attempts to find the association between single nucleotide polymorphism (SNP) of IL2+166 gene (rs2069763) and type 2 diabetes mellitus (T2DM) in a sample of Iraqi patients. A total of 44 patients and 55 apparently healthy volunteers were genotyped for the SNP using polymerase chain reaction test. Three genotypes (GG, GT, and TT) corresponding to two alleles (G and T) were found to have SNP. Both study groups’ genotypes had a good agreement for the analysis of Hardy-Weinberg Equilibrium. The results revealed increased frequencies between the observed and expected GG and TT genotypes and IL2+166 SNP T allele in T2DM  patients (40.9 vs. 40.0 %; OR = 1.04; 95% CI, 0.47 - 2.31), whereas the values in the control group were

A numerical model for Polypropylene 575 polymer melts flow along the solid conveying screw of a single screw extruder under constant heat flux using ANSYS-FLUENT 17.2 software has been conducted. The model uses the thermophysical properties such as Viscosity, thermal conductivity, Specific heat and density of polypropylene 575 that measured as a function of temperature, and residence time data for process simulation. The numerical simulation using CFD models for single screw extruder and the polymer extrusion was analysed for parameters such as (thermal conductivity, specific heat, density and viscosity) reveals a high degree of similarity to experimental data measured. The most important outcome of this study is that geometrical, parame