The seismic method depends on the nature of the reflected waves from the interfaces between layers, which in turn depends on the density and velocity of the layer, and this is called acoustic impedance. The seismic sections of the East Abu-Amoud field that is located in Missan Province, south-eastern Iraq, were studied and interpreted for updating the structural picture of the major Mishrif Formation for the reservoir in the field. The Mishrif Formation is rich in petroleum in this area, with an area covering about 820 km2. The horizon was calibrated and defined on the seismic section with well logs data (well tops, check shot, sonic logs, and density logs) in the interpretation process to identify the upper and lower boundaries of the Formation. Seismic attributes were used to study the formation, including instantaneous phase attributes and relative acoustic impedance on time slice of 3D seismic data . Also, relative acoustic impedance was utilized to study the top of the Mishrif Formation. Based on these seismic attributes, karst features of the formation were identified. In addition, the nature of the lithology in the study area and the change in porosity were determined through the relative acoustic impedance The overlap of the top of the Mishrif Formation with the bottom of the Khasib Formation was determined because the Mishrif Formation is considered as an unconformity surface.
The present study deals with processing of one seismic line (2WL2) with a length of (37km) for (2D) seismic data of west Luhais area that is located within the administrative borders of the province of Muthanna in south of Iraq. The quality of the recorded data of this line is in general weak due to the effect of noise mainly. The study was made up in oil Exploration Company by utilizing OMEGA software which consists of a great number of the processing programs. The elevation static correction and residual static correction were applied on the studied line and the final section were resulted after completing the treatment processes that proceed followed of the static correction process and the result of elevation static correcting was go
... Show MoreThe characterizations of reservoir require reliable knowledge of certain fundamental reservoir properties. Log measurements can define or at least infer these properties: resistivity, porosity, shale volume, lithology, and water, oil, or gas saturation and permeability. The current study represents evaluation of petrophysical properties in well LU-12 for Zubair Formation in Luhais Oil Field, southern Iraq. The petrophysical evaluation was based on geophysical well logs data to delineate the reservoir characteristics of Zubair Formation. The available geophysical well logs such as (sonic, density, neutron, gamma ray, SP, and resistivity logs) are digitized using the Didger software. The environmental corrections and petrophysical paramete
... Show MoreIn many oil-recovery systems, relative permeabilities (kr) are essential flow factors that affect fluid dispersion and output from petroleum resources. Traditionally, taking rock samples from the reservoir and performing suitable laboratory studies is required to get these crucial reservoir properties. Despite the fact that kr is a function of fluid saturation, it is now well established that pore shape and distribution, absolute permeability, wettability, interfacial tension (IFT), and saturation history all influence kr values. These rock/fluid characteristics vary greatly from one reservoir region to the next, and it would be impossible to make kr measurements in all of them. The unsteady-state approach was used to calculate the relat
... Show MoreSpatial data analysis is performed in order to remove the skewness, a measure of the asymmetry of the probablitiy distribution. It also improve the normality, a key concept of statistics from the concept of normal distribution “bell shape”, of the properties like improving the normality porosity, permeability and saturation which can be are visualized by using histograms. Three steps of spatial analysis are involved here; exploratory data analysis, variogram analysis and finally distributing the properties by using geostatistical algorithms for the properties. Mishrif Formation (unit MB1) in Nasiriya Oil Field was chosen to analyze and model the data for the first eight wells. The field is an anticline structure with northwest- south
... Show MoreThe seismic reflection method has a primary role in petroleum exploration. This research is a structural interpretation study of the 2D seismic reflection survey carried out in the Upper West Euphrates (Khan Al-Baghdadi area), which is located in the western part of Iraq, Al-Anbar governorate. The two objectives of this research are to interpret Base Akkas/Top Khabour reflector and to define potential hydrocarbon traps in the surveyed area. Based on the synthetic seismogram of Akk_3 well near the study area, the Akkas/Top Khabour reflector was identified on the seismic section. Also, the Silurian Akkas Hot_shale reflector was identified and followed up, which represents the source and seal rocks of the Paleozoic
... Show MoreThe EMERGE application from Hampsson-Russell suite programs was used in the present study. It is an interesting domain for seismic attributes that predict some of reservoir three dimensional or two dimensional properties, as well as their combination. The objective of this study is to differentiate reservoir/non reservoir units with well data in the Yamama Formation by using seismic tools. P-impedance volume (density x velocity of P-wave) was used in this research to perform a three dimensional seismic model on the oilfield of Nasiriya by using post-stack data of 5 wells. The data (training and application) were utilized in the EMERGE analysis for estimating the reservoir properties of P-wave ve
... Show MoreThe Mishrif Formation (Cenomanian – Early Turonian) is an important geologic formation in southern Iraq due to its petrophysical properties and geographic extensions, making it a good reservoir of hydrocarbons. Petrophysical properties of the Mishrif Formation in the current study at the Nasiriya oil field were determined from the interpretation of three open-hole logs data of (NS-1, NS-2, and NS-3) wells.
The results of the Mishrif petrophysical evaluation showed that the formation consists of five variable units (CRI, MA, CRII, MB1 and MB2), each one characterized by distinct petrophysical characteristics.
The upper (MA) and lower (MB) units were determined using electrical, porosity and gamma-ray logs. A sha
... Show MorePetrophysical properties evaluation from well log analysis has always been crucial for the identification and assessment of hydrocarbon bearing zones. East Baghdad field is located 10 km east of Baghdad city, where the southern area includes the two southern portions of the field, Khasib formation is the main reservoir of East Baghdad oil field.
In this paper, well log data of nine wells have been environmentally corrected, where the corrected data used to determine lithology, shale volume, porosity, and water saturation. Lithology identified by two methods; neutron-density and M-N matrix plots, while the shale volume estimated by single shale indicator and dual shale indicator, The porosity is calculated from the three common po
... Show MoreThis study deals with the seismic reflection interpretation of lower Cretaceous Formations in Dhufria area, including structural and stratigraphic techniques. In the interpretation process, the 3-D seismic data volume and well logs have been used. Based on well logs and synthetic traces two horizons were identified and picked which are the top and bottom of Zubair Formation. These horizons were followed over all the area in order to obtain structural setting as well as studying Kirkuk group Formation of Tertiary age which represents highstand progradational seismic facies.
A 3D geological model is an essential step to reveal reservoir heterogeneity and reservoir properties distribution. In the present study, a three-dimensional geological model for the Mishrif reservoir was built based on data obtained from seven wells and core data. The methodology includes building a 3D grid and populating it with petrophysical properties such as (facies, porosity, water saturation, and net to gross ratio). The structural model was built based on a base contour map obtained from 2D seismic interpretation along with well tops from seven wells. A simple grid method was used to build the structural framework with 234x278x91 grid cells in the X, Y, and Z directions, respectively, with lengths equal to 150 meters. The to
... Show More