Two factorial experiments were conducted. One of them was laboratory experiment which was carried out at the Laboratory of Agriculture and Marshes College, University of Thi-Qar during laboratories of certification and test of seeds office in Thi-Qar governorate–Nassiriyah district during 2015. The other was conducted at the lath house with used the pots during spring season of 2016. The aim was to investigate the effect of soybean seeds priming before sowing on seed vigour and seedling growth characteristics under salinity stress. The design of Lab. experiment was (CRD) while for the other experiment was (RCBD) with four replications. Each experiment consisted of two factors. The first factor included seeds soaking treatments for 24 hours with KCL 10 g L-1, KCL 20 g L-1 and seeds soaking in distilled water, in addition to un soaked seeds treatment. The second factor was seeds planting in four levels of salinity 0, 2, 4 and 6 ds m-1. The results of Laboratory experiment showed that superiority soybean seeds soaked with KCL 20 g L-1 in given highest averages of germination speed, standard germination percentage, radical length, plumule length, seedling dry weight and seedling vigour index. Soybean seeds were germinated in distilled water media (control) gave highest averages in all of studied traits. The results of Laboratory experiment also showed that soybean seeds soaked with KCL 20 g L-1 led to improved the seeds germination and seedling growth traits under salinity stress. The results of pots experiment showed that superiority soybean seeds soaked with KCL 20 g L-1, in given highest averages of field emergence percentage, plant length and plant dry weight .Soybean seeds were sowed in distilled water media gave highest average in all of studied traits. The results of pots experiment also showed that soybean seeds soaked with KCL 20 g L-1 led to improved emergence percentage, plant growth under salinity stress.
In this paper, a new equivalent lumped parameter model is proposed for describing the vibration of beams under the moving load effect. Also, an analytical formula for calculating such vibration for low-speed loads is presented. Furthermore, a MATLAB/Simulink model is introduced to give a simple and accurate solution that can be used to design beams subjected to any moving loads, i.e., loads of any magnitude and speed. In general, the proposed Simulink model can be used much easier than the alternative FEM software, which is usually used in designing such beams. The obtained results from the analytical formula and the proposed Simulink model were compared with those obtained from Ansys R19.0, and very good agreement has been shown. I
... Show More
In this work, strains and dynamic crack growth were studied and analyzed in thin flat plate with a surface crack at the center, subjected to cycling low velocity impact loading for two types of aluminum plates (2024, 6061). Experimental and numerical methods were implemented to achieve this research. Numerical analysis using program (ANSYS11-APDL) based on finite element method used to analysis the strains with respect to time at crack tip and then find the velocity of the crack growth under cycling impact loading. In the experimental work, a rig was designed and manufactured to applying the cycling impact loading on the cracked specimens. The grid points was screened in front of the crack tip to measure the elastic-plas
... Show MoreGlobal warming has had considerable effects on vital ecosystems, which has also been caused by increased temperatures and CO2 that follow changes in different abiotic factors, which poses threats to mangrove forests environment. This research was conducted to examine the physiological and morphological characteristics of the Rhizophora apiculata mangrove regarding higher air temperature for the variety of tree species that respond to climate change. Seedlings were cultivated for three months in regulated growth chambers with three varying temperatures of 38°C, 21°C under CO2 at 450 ppm, and ambient CO2 concentration i.e., 450 ± 20 ppm under average temperature at 28°C as the control condition
... Show More
(2)
(1)
In this study, the induced splined shaft teeth contact and bending stresses have been investigated numerically using finite element method(Ansys package version 11.0) with changing the most effecting design parameter,(pressure angle, teeth number, fillet radius and normal module), for internal and external splined shaft. Experimental work has been achieved using two dimensional photoelastic techniques to get the contact and bending stresses; the used material is Bakelite sheet type “PSM-4”.
The results of numerical stress analysis indicate that, the increasing of the pressure angle and fillet radius decrease the bending stress and increase the contact stress for both internal and external spline shaft teeth while the increasing of
(1)
(2)
Microwave heating is caused by the ability of the materials to absorb microwave energy and convert it to heat. The aim of this study is to know the difference that will occur when heat treating the high strength aluminum alloys AA7075-T73 in a microwave furnace within different mediums (dry and acidic solution) at different times (30 and 60) minutes, on mechanical properties and fatigue life. The experimental results of microwave furnace heat energy showed that there were variations in the mechanical properties (ultimate stress, yielding stress, fatigue strength, fatigue life and hardness) with the variation in mediums and duration times when compared with samples without treatment. The ultimate stress, yielding stress and fatigue streng
... Show More
A pots experiment was conducted in the plastic house of Kalar Horticulture station Province of Sulaimania, by using soil brought from one of Kalar region fields during growing season of 2007-2008, to study the effect of increasing levels of urea fertilizer which is (0, 0.20,0.40,0.80) g/pot which equals to (0,100,200,400) kg urea/ha, and super phosphate fertilizer which is (0,0.24,0.48)gm/pot which is equal (0,120,240) kg sup/ha, in nutrition state of wheat IPA 95 component, clay determining Nitrogen, Phosphor and Potassium content in green part and seeds. The Completely Randomized Design was used with three replication per t
... Show MoreThe present study aimed to investigate the effects of alcohol and hot aqueous extracts for leaves of Adhatoda vasica on, first larval instars Musca domestica. They were exposed to the suggested concentrations of alcoholic extract which were (500, 1000, 1500, 2000) PPM while the suggested concentrations of the hot aqueous extracts (500, 1000, 1500, 2000, 2500)PPM. The alcoholic (Methanol) extract of leaves was much effective on to killing the first larval instars of the M. domestica than hot aqueous extract.
A biological experiment was conducted in the field of Biology Department-College of Education (Ibn Al-Haitham) University of Baghdad for growing season of (2004-2005), to study the effect of two varieties of the fenugreek plant (Trigonella foenum – graeccum L.) and gibberellic acid concentration (0, 25, 50, 100, 125) part per million and duration of four spraying (15, 20, 25, 30) day determining concentration medicinal active saponine compounds like (Trigonelline, choline, Carpaine and Gentianine). The experiment was performed according to complete Randomize Complete Blocks Design (RBCD) by three replicate was adopted, means were compared by using the least significant difference at (0.05) probability level. Results showed t
... Show MoreA biological experiment was conducted to study the effect of different concentrations of gibberellic acid and urea fertilizer and their interactions in some characteristic related to green growth of fenugreek plant (Trigonella foenum-graecum L.) in the green house of Department of Biology in College of Education (IbnÂalÂHaitham)/Baghdad University for the growth season (2008Â2009) in pots of (5 kgm) soil per pot, and four concentrations of gibberellic acid were used, they are (0,25,50,100) ppm, these concentrations were sprayed after the perfection of the fourth leaf for the plant. Moreover, three levels of urea fertilizer were used, they were (0.25, 0.50, 1.00) gm/pot. These concentrations were added as two p
... Show More