Several million tons of solid waste are produced each year as a result of construction and demolition activities around the world, and brick waste is one of the most widely wastes. Recently, there has been growing number in studies that conducted on using of recycling brick waste (RBW) to produce environmentally friendly concrete. The use of brick waste (BW) as potential partial cement or aggregate replacement materials is summarized in this review where the performance is discussed in the form of the mechanical strength and properties that related to durability of  concrete. It was found that, because the pozzolanic activity of clay brick powder, it can be utilized as substitute for cement in replacement level up to 10%. Whereas,

This paper presents a vibration suppression control design of cantilever beam using two piezoelectric ‎patches. One patch was used as ‎an actuator element, while the other was used as a sensor. The controller design was designed via the balance realization reduction method to elect the reduced order model that is most controllable and observable. ‎the sliding mode observer was designed to estimate six states from the reduced order model but three states are only used in the control law. Estimating a number of states larger than that used is in order to increase the estimation accuracy. Moreover, the state ‎estimation error is proved bounded. An ‎optimal LQR controller is designed then using the ‎estimated states with the slid

Ground penetrating radar (GPR) is one of the geophysical methods that utilize electromagnetic waves in the detection of subjects below the surface to record relative position and shape of archaeological features in 2D and 3D. GPR method was applied in detecting buried archaeological structure in study area in a location within the University of Baghdad. GPR with 3D interpretation managed to locate buried objects at the depth of (1m) . GPR Survey has been carried (12) vertical lines and (5) horizontal lines using frequency antenna (500) MHZ .

Because of Citrobacter freundii medical and economical importance and that there are only little local studies about it, this study aimed to isolate and identify this important bacterial species from others that have a similar biochemical and morphological characteristics. Twenty five chicken meat samples were collected randomly from local markets in Baghdad city during 2017; Citrobacter was isolated from the collected samples using selective and differential media and identified using biochemical tests, the identification was confirmed using Vitek 2 compact and polymerase chain reaction for 16S rRNA and the isolated bacteria identified as C. freundii.

     An experimental study was carried out to improve the surface roughness quality of the stainless steel 420 using magnetic abrasive finishing method (MAF). Four independent operation parameters were studied (working gap, coil current, feed rate, and table stroke), and their effects on the MAF process were introduced. A rotating coil electromagnet was designed and implemented to use with plane surfaces. The magnetic abrasive powder used was formed from 33%Fe and 67% Quartz of (250µm mesh size). The lubricant type SAE 20W was used as a binder for the powder contents. Taguchi method was used for designing the experiments and the optimal values of the selected parameters were found. An empirical equation representing the r

This research presents a particular designing strategy for a free form of surfaces, constructed by the lofting design method. The regarded surfaces were created by sliding a B-spline curves (profile curves), in addition to describing an automatic procedure for selective identification of sampling points in reverse engineering applications using Coordinate Measurement Machine. Two models have been implemented from (Ureol material) to represent the different cases of B-spline types to clarify its scope of application. The interior data of the desired surfaces was designed by MATLAB software, which then were transformed to UG-NX9 software for connecting the sections that were designed in MATLAB program and obtaining G-code programs for the

Artemia fransiscana is one of the most important live food for commercial larval aquaculture. The aim of this study is to investigate the effects of 890 nm diode laser irradiation on Artemia capsulated cysts using (1-10) minutes exposure time, and 2.26x10-3 J/cm2 Fluence. The Artemia samples were obtained from two locations: Dyalaa and Basraa. After irradiation, hatching percentage (H %) and hatching efficiency(HE) of Artemia were measured after 24 and 48 hours of incubation. The results of the effect of laser light on the capsulated cysts from Dyalaa showed that the optimum dose for enhancing (H %) after 24 hours of incubation is using 10 minutes exposure time, while after 48 hours of incubation the (H %) enhancement can be achieved

Humans are exposed to nuclear radiations every day, and these radiations are both natural and artificial. When the body tissues are exposed to nuclear radiation, free radicals are formed, which are responsible for cancer development. In this research, silver nanoparticles were synthesized by electrical explosion wire method. Nanoparticles were added to deionized water that contained free radicals before and after exposure to gamma rays. The obtained results indicate that the silver nanoparticles have antioxidant potential through possessing free radical scavenging activity, as they can donate electron to free radicals and become neutralize. Then, these nanoparticles were injected to mice before and after their irradiation with gamma ray.

Modern automation robotics have replaced many human workers in industrial factories around the globe. The robotic arms are used for several manufacturing applications, and their responses required optimal control. In this paper, a robust approach of optimal position control for a DC motor in the robotic arm system is proposed. The general component of the automation system is first introduced. The mathematical model and the corresponding transfer functions of a DC motor in the robotic arm system are presented.  The investigations of using DC motor in the robotic arm system without controller lead to poor system performance. Therefore, the analysis and design of a Proportional plus Integration plus Divertive (PID) controller is illustrated.