In this paper, a single link flexible joint robot is used to evaluate a tracking trajectory control and vibration reduction by a super-twisting integral sliding mode (ST-ISMC). Normally, the system with joint flexibility has inevitably some uncertainties and external disturbances. In conventional sliding mode control, the robustness property is not guaranteed during the reaching phase. This disadvantage is addressed by applying ISMC that eliminates a reaching phase to ensure the robustness from the beginning of a process. To design this controller, the linear quadratic regulator (LQR) controller is first designed as the nominal control to decide a desired performance for both tracking and vibration responses. Subsequently, discontinuous con

In this work; copper oxide films (CuO) were fabricated by PLD. The films were analyzed by UV-VIS absorption spectra and their thickness by using profilometer. Pulsed Nd:YAG laser was used for prepared CuO thin films under O₂ gas environment with varying both pulse energy and annealing temperature. The optical properties of   as-grown film such as optical transmittance spectrum, refractive index and energy gap has been measured experimentally and the effects of laser pulse energy  and annealing temperature on it were studied. An inverse relationship between energy gap and both annealing temperature and pulse energy was observed.

Embracing digital technological advancements in media and communication has led government entities to adopt communication practices fully aligned with the digital and networked system in government communication. Traditional media practices within the government environment increasingly rely on the ability to utilize digital tools and systems for content creation, communication, evaluation, and the management of the entire communication process within an electronic and intelligent framework for government services. Naturally, this transformation has caught the attention of communication and public relations researchers worldwide, as the digital and networked aspects of government communication now form an intelle

     In this study, cadmium oxide (CdO) was deposited on glass bases by thermal chemical spraying technique at three concentrations (0.05, 0.1, 0.15) M and then was irradiated by CO₂ laser with 10.6 μm wave length and 1W power. The results of the atomic force microscope AFM test showed that the surfaces of these CdO thin films were homogenous and that the laser irradiated effect resulted in decreasing the roughness of the surface as well as the heights of the granular peaks, indicating a greater uniformity and homogeneity of the surfaces. The optical properties were studied to determine laser effect. The results of optical tests of these thin films showed that the photoluminescence spectra and absorption s

In this work, (CdO)1-x (CoO)x thin films were prepared on glass slides by laser-induced plasma using Nd:YAG laser with (λ=1064 nm) and duration (9 ns) at different laser energies (200-500 mJ) with ratio (x=0.5), The influence of laser energy on structural and optical properties has been studied. XRD patterns show the films have a structure of polycrystalline wurtzite. As for AFM tests results for the topography of the surface of the film, where the results showed that the grain size and the average roughness increase with increasing laser energy. The optical properties of all films were also studied and the results showed that the absorption coefficient for within the wavelength range (280-1100 nm), The value of the optical power gap fo

􀀨􀀅􀀆􀀔􀀜􀀄􀀂􀀆􀀈􀀓􀀌􀀩􀀏􀀆􀀉􀀅􀀆􀀉􀀅􀀉􀀚􀀝􀀔􀀄􀀗􀀉􀀚􀀆􀀂􀀓􀀚􀀁􀀔􀀄􀀓􀀅􀀆􀀄􀀂􀀆􀀔􀀓􀀆􀀃􀀂􀀔􀀄􀀟􀀉􀀔􀀃􀀆􀀔􀀜􀀃􀀆􀀛􀀃􀀜􀀄􀀗􀀚􀀃􀀆􀀗􀀌􀀄􀀔􀀄􀀗􀀉􀀚􀀆􀀂􀀘􀀃􀀃􀀊􀀂􀀆􀀓􀀖􀀆􀀓􀀛􀀃􀀌􀀔􀀁􀀌􀀅􀀄􀀅􀀕􀀢􀀆􀀪􀀜􀀃􀀆􀀄􀀅􀀛􀀃􀀂􀀔􀀄􀀕􀀉􀀔􀀄􀀓􀀅􀀂􀀆 􀀉􀀌􀀃􀀆􀀙􀀉􀀂􀀃􀀊􀀆􀀓􀀅􀀆􀀉􀀁􀀔􀀓􀀟􀀓􀀙􀀄􀀚􀀃􀀆􀀚􀀉􀀔􀀃􀀌􀀉􀀚􀀆􀀂􀀘􀀉􀀗􀀃􀀆􀀟􀀄􀀊􀀂􀀔􀀆􀀔􀀜􀀃􀀆􀀗􀀃􀀅􀀔􀀃􀀌􀀚􀀄􀀅􀀃􀀂􀀆􀀓􀀖􀀆􀀔􀀜􀀃􀀆􀀙􀀉􀀂􀀃􀀆

An optical video communication system is designed and constructed using pulse frequency modulation (PFM) technique. In this work PFM pulses are generated at the transmitter using voltage control oscillator (VCO) of width 50 ns for each pulse. Double frequency, equal width and narrow pulses are produced in the receiver be for demodulation. The use of the frequency doubling technique in such a system results in a narrow transmission bandwidth (25 ns) and high receiver sensitivity.

   There is no doubt that the project control function is very important for administration, so the project Management depends on to monitor and control the project. The project control integrated to the planning which is the base of the administration functions; planning, organizing, directing, and controlling. Without project control cannot be insure to fulfill the plan of the project by the budget and specified time. The project management apply many methods of control to achieve the goals of project which are cost, time, and required specifications. Earned Value Management one of control methods that used in the project by international companies.

Earned Value Method is used in the project o

The issue of the research lies in the non-representation of the models developed for the communication process in the interaction and networking processes through social media, as the research sought to build a network model of communication according to the specific data and features of social media platforms in order to reach a special generalization to understand how the process of networking operates in cyberspace.

The researcher followed the analytical survey approach as she described the communication models outwardly in order to be able to build a networked communication model that represents the flow of post-reactive communication. Therefore, it has been named "Nebula - Sadeem" after the concept of post-space and cosmic g