Abstract Introduction: MMP3 plays a crucial role in the process of bone erosion in the pathomechanism of rheumatoid arthritis (RA). It acts by removing the outer osteoid layer, which allows the osteoclasts to tightly connect and carry out the subsequent damage to the underlying bone. MMP3 can trigger the production of other MMPs like MMP-1, MMP-7, and MMP-9, it plays a pivotal role in the remodeling of connective tissues. Aim of the study: to assess the influence of MMP-3 serum levels and single-nucleotide polymorphisms of rs679620 in the rheumatoid arthritis patients' group in comparison to the control group. Subjects: eighty eight samples, 45 rheumatoid arthritis patients after being referred by their treating physician for regular RA test. The remaining 43 samples all represent apparently healthy people. The present study investigated the serum concentration of MMP-3 and rs679620 SNPs in the group of patients with RA, in comparison to the control group. Results: The results indicated a significant elevation in MMP-3 levels in RA patients in comparison to healthy individuals (12.75 ± 0.38 vs. 9.69 ± 0.37) and the findings of rs679620 SNPs appeared that the patient group has a non-significant increase in both allele frequency A and genotype frequency AA when compared to the control group (66.2 vs. 52.2 %; p = 0.172; OR = 1.79 and 35.3 vs. 17.4 %; p = 0.229; OR = 2.59) , but a non-significant decrease in both allele frequency C and genotype frequency CC when compared to the control group (2.94 vs. 4.4 %; p = 1.0; OR = 0.67 and 2.9 vs. 4.3 %; p = 1.0; OR = 0.67), as well as a non-significant decrease in allele frequency G and both genotypes frequency GG and AG when compared to the control group (30.9 vs. 43.5 %; p = 0.233; OR = 0.58, 0.0 vs. 8.7 %; p = 0.159; OR = 0.12 and 61.8 vs. 69.6 %; p = 0.585; OR = 0.71 ). Patients carrying the AA and AG genotype, had significantly higher serum levels of MMP-3 compared to control (P= 0.005 and 0.004) respectively. Conclusion: Rs679620 may influence joint destruction via increase MMP-3 production.
This work predicts the effect of thermal load distribution in polymer melt inside a mold and a die during injection and extrusion processes respectively on the structure properties of final product. Transient thermal and structure models of solidification process for polycarbonate polymer melt in a steel mold and die are studied in this research. Thermal solution obtained according to solidify the melt from 300 to 30Cand Biot number of 16 and 112 respectively for the mold and from 300 to 30 Cand Biot number of 16 for die. Thermal conductivity, and shear and Young Modulus of polycarbonate are temperature depending. Bonded contact between the polycarbonate and the steel surfaces is suggested to transfer the thermal load. The temperat
... Show MoreThe concepts of higher Bi- homomorphism and Jordan higher Bi- homomorphism have been introduced and studied the relation between Jordan and ordinary higher Bi- homomorphism also the concepts of Co- higher Bi- homomorphism and Co- Jordan higher Bi- homomorphism introduced and the relation between them in Banach algebra have also been studied.
Reconstruction in Iraq requires coherent legitimate frameworks that are able to detail obligations, rights and responsibilities of the parties participating in reconstruction projects, regardless their type or delivery system.
Conditions of Contract can be considered an important component of these frameworks. This paper investigates flexibility and appropriateness of the application of Iraqi conditions of contract in reconstruction projects. These conditions were compared to FIDIC Conditions. The objective wasn't comparing individual clauses, but rather exploring the principles and philosophy laying behind each conditions, and to what extent each conditions care about realizing equity between main contract parties. Validity of applic
Experimental study of heat transfer coefficients in air-liquid-solid fluidized beds were carried out by measuring the heat rate and the overall temperature differences across the heater at different operating conditions. The experiments were carried out in Q.V.F. glass column of 0.22 m inside diameter and 2.25 m height with an axially mounted cylindrical heater of 0.0367 m diameter and 0.5 m height. The fluidizing media were water as a continuous phase and air as a dispersed phase. Low density (Ploymethyl-methacrylate, 3.17 mm size) and high density (Glass beads, 2.31 mm size) particles were used as solid phase. The bed temperature profiles were measured axially and radially in the bed for different positions. Thermocouples were connecte
... Show MoreThe presence and prevalence of V. cholerae were investigated in forty five water samples collected from different locations of Tiger River/ Baghdad city. Twenty one isolates were isolated by adopting a simple isolation techniques. The final identification revealed that only three isolates were confirmed as V. cholerae. They were named 1J, 1R and Dial 131 which are all serogrouped as non-O1. Toxin Coregulated Pili (TCP) and heat labile enterotoxin (LT) were determined in only the environmental isolate 1J while non of the isolates produced heat stabile toxin (ST). The purification scheme was improved, few steps were adopted to include back extraction of ammonium sulfate, saturation between 80-20%, desalting through Sephadex G25, and gel filt
... Show MoreBaTiO3 thin films have been deposited on Si (111) and glass substrates by using pulsed laser deposition technique. The films were characterized by using X-ray diffraction, atomic force microscope and optical transmission spectra. The films growth on Si after annealing at 873K showed a polycrystalline nature, and exhibited tetragonal structure, while on glass substrate no growth was noticed at that temperature. UV-VIS transmittance measurements showed that the films are highly transparent in the visible wavelength region and near-infrared region for sample annealing on glass substrate. The optical gap of the film were calculated from the curve of absorption coefficient (αhν) 2 vs. hν and was found tobe 3.6 eV at substrate temperature 5
... Show MoreDC planar sputtering system is characterized by varying discharge potential of (250-2000 volt) and Argon gas pressures of (3.5×10-2 – 1.5) mbar. The breakdown voltage for silver electrode was studied with a uniform electric field at different discharge distances, as well as plasma parameters. The breakdown voltage is a product of the Argon gas pressure inside the chamber and gab distance between the electrodes, represent as Paschen curve. The Current-voltage characteristics curves indicate that the electrical discharge plasma is working in the abnormal glow region. Plasma parameters were found from the current-voltage characteristics of a single probe positioned at the inter-cathode space. Typical values of the electron temperature an
... Show MoreUreteric obstruction is rarely noted in cases of gastric cancer. Its involvement by distant metastasis from gastric adenocarcinoma without direct invasion is an exceptionally unusual occurrence. This is the story of a 58-year-old man who arrived at the emergency department with acute flank pain and fever. He was initially diagnosed with obstructive pyelonephritis after the discovery of a new onset, complete ureteric obstruction on the left side. Subsequent investigations and follow-up revealed the presence of gastric adenocarcinoma with possible ureteric metastasis bilaterally, flank pain and hydronephrosis were the first and only presentations of gastric cancer. The rarity of the condition and the unusual presentation encouraged us to r
... Show MoreIn The Name of Allah Most Gracious Most Merciful
The reason for choosing this topic was:
First: It is my great love for the Prophet Muhammad, may God’s prayers and peace be upon him, his family, his companions, his followers, the followers of their followers, and the scholars after them until the Day of Judgment.
Secondly: Showing a great jurisprudential figure who has contributed by speaking about important jurisprudential issues in the life of this nation, and bringing out this immortal book to put it in the hands of scholars, so I chose a figure from the followers (may God be pleased with them all).
Third: The study of the jurisprudence of the companions