In this article the conventional "solid-state reaction" method was used to synthesize perovskite Li0.4Cd0.6Ba2Ca2Cu3O10+δ. Four main types of compounds were obtained by physically replacing calcium oxide with cadmium in proportions 0, 0.03, 0.06 and 0.09, the pure Li0.4Cd0.6Ba2Ca2Cu3O10+δ phase, and the phases Li0.4Cd0.6Ba2Ca1.97Cd0.03Cu3O10+δ and Li0.4Cd0.6Ba2Ca1.94Cd0.06Cu3O10+δ and Li0.4Cd0.6Ba2Ca1.91Cd0.09Cu3O10+δ ,respectively from mixing their constituent oxides and pressed into pelts and then sintered in the furnace at 850 degrees Celsius for 90 hours: These samples have been studied for their original dielectrically properties. The real dielectric constant, dielectric loss factor, and tangent were calculated in the frequency range (50 to 1000000 HZ). It was found that the partial substitution of cadmium oxide plays an important role in enhancing dielectrically properties.
Westiellopsis prlifica was exposed to 1, 2, 3, 5, 7 and 10 ppm from both lead & Cadmium, in order to measure their capacity to remove these metals from the polluted aquatic environment and to study its ability to tolerant them. The algae were grown under optimum conditions.
Westiellopsis prlifica had the ability to remove the lead with percentages about 31.57, 54.42, 62.35, 61.8, 57.02 and 68.34% for the concentrations 1, 2, 3, 5, 7 and 10 ppm, respectively, but it was found that these percentages were be better in the last day of the experiment for some of the concentrations 1, 2 and 3 ppm, While the tolerant of it to lead was up to the concentration 10 ppm.
Westiellopsis prlifica appears ability to remove Cadmium with percent
The objective of this research is to study experimentally and theoretically the girder vertical load share of the curved I-Girder bridges subjected to the point load in addition to the self-weigh and supper imposed dead loads. The experimental program consist of manufacturing and testing the five simply supported bridge models was scaled down by (1/10) from a prototype of 30m central span. The models carriageway central radii are 30 m, 15m or 10m. The girder spacing of the first two models is 175 mm with an overall carriageway width of 650mm. The girder spacing of the other three bridge models is 200mm with the overall carriageway width of 700 mm. The overall depth of the composite section was 164 mm. To investigate the effect of live load
... Show MoreIn an intensive study of the various species of the Euglenophyceae under different environmental conditions, the algal samples were collected monthly in twelve springs and six related streams from September 2019 to August 2020 within Shaglawa district-Erbil Province in virgin areas for phycolimnological study. Twenty species of Euglenophyceaen are identified as a new record for the algal flora. These taxa consist of Colacium vesiculosum, Lepocinclis salina and L.wangi, Eutreptia viridis, Euglena chlamydophora, E. clavata,
... Show MoreEtude de I' espace dans un extrait de Les sequestres d' Altona de Jean
n this research, several estimators concerning the estimation are introduced. These estimators are closely related to the hazard function by using one of the nonparametric methods namely the kernel function for censored data type with varying bandwidth and kernel boundary. Two types of bandwidth are used: local bandwidth and global bandwidth. Moreover, four types of boundary kernel are used namely: Rectangle, Epanechnikov, Biquadratic and Triquadratic and the proposed function was employed with all kernel functions. Two different simulation techniques are also used for two experiments to compare these estimators. In most of the cases, the results have proved that the local bandwidth is the best for all the types of the kernel boundary func
... Show MoreCadmium oxide CdO thin films were prepared by successive ionic layer adsorption and reaction (SILAR) technique at varying number of dippings. The CdO thin films were prepared from a source material of Cadmium acetate and ammonium hydroxide solution deposited on glass substrate at 95℃. The prepared thin films were investigated by X-ray diffraction (XRD), Atomic force microscopy (AFM), Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR), and UV-Visible spectrometry. The XRD analysis reveals that the films were polycrystalline with cubic structure having preferential orientation along (1 1 1), (2 0 0), (2 2 0), and (3 1 1) planes. While the tests of the scanning electron microscopy and the atomic force mic
... Show More