In this study, a one-dimensional model represented by Butler-Volmer-Monod (BVM) model was proposed to compute the anode overpotential and current density in a mediator-less MFC system. The system was fueled with various organic loadings of real field petroleum refinery oily sludge to optimize the favorable organic loading for biomass to operate the suggested system. The increase in each organic loading showed higher resistance to electrons transport to the anode represented by ohmic loss. On the contrary, both activation and mass transfer losses exhibited a noticeable decrement upon the increased organic loadings. However, current density was improved throughout all increased loads achieving a maximum current density of 5.2 A/m³

The present study focuses on the biological strategy for treating cancer and parasitic infections, such as leishmaniasis antiparasitic activity, forthe crude alcoholic extract ofFicus leaves and their extracted total flavonoids with a comparison between their effects.The flavonoids were extracted from the leaves of the mature Ficuscaricausing the reflux extraction method. Total flavonoids were detected qualitatively by TLC techniquewhich demonstratedthat the plant was rich indifferent flavonoids, especially Rutin, Quercetin, Kaempferol, luteolin and others. Quantitatively, the plant total flavonoids content was 337.3 mg / 100 g fig leaves calculated as rutin.The biologicaleffects of the crude and purified total flavonoi

This work presents the modeling of the electrical response of monocrystalline photovoltaic module by using five parameters model based on manufacture data-sheet of a solar module that measured in stander test conditions (STC) at radiation 1000W/m² and cell temperature 25 . The model takes into account the series and parallel (shunt) resistance of the module. This paper considers the details of Matlab modeling of the solar module by a developed Simulink model using the basic equations, the first approach was to estimate the parameters: photocurrent I_ph, saturation current I_s, shunt resistance R_sh, series resistance R_s, ideality factor A at stander test condition (STC) by an ite

Photovoltaic devices (PVs) were fabricated by spray-coating an ink of copper indium diselenide CuInSeR 2 R(CIS) nanocrystals as the light-absorbing layer. Without high-temperature post-deposition annealing, PVs were made on glass substrates with power conversion efficiencies of up to 1.5% and 0.9%, for Au and Mo coated respectively, under AM 1.5 illumination. UV–Vis spectrophotometer in the wavelength range 350–1500 nm. X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS) analysis it is evident that CuInSeR 2 R have the chalcopyrite structure as the major phase and no secondary phase with a preferred orientation along (112) direction and The atomic ratio of Cu : In : Se in the nanocrystals is nearly 1 : 1 : 2.

In this study, we report a statistical study for the relationship between coronal mass ejections (CMEs) and sunspot number (SSN) that were registered during the period 2008-2017 for the solar cycle 24. SSN was extracted from Sunspot Index and Long-term Solar Observations (SILSO), while CMEs number from observations made by the Large Angle and Spectrometric Coronagraph (LASCO) on board the Solar and Heliospheric Observatory mission (SOHO). The present period was adopted to conduct the investigation and obtain the mutual correlation between SSN and CMEs. The relationship between CME, the speed of halo CME, and partial halo CMEs for solar cycle 24 were studied. The analysis of results indicated that the average speed of halo CMEs is almost

In this study, pebble bed as an absorber and storage material was placed in a south facing, flat plate air-type solar collector at fixed tilt angle of (45°). The effect of this material and differ- ent parameters on collector efficiency has been investigated experimentally and
theoretically. Two operation modes were employed to study the performance of the solar air heater. An inte- grated mode of continuous operation of the system during the period of (11:00 am – 3:00 pm) and non-integrated mode in which the system stored the solar energy through the day then used the stored energy during the period of (3:00 pm – 8:00 pm). The results of parametric study in case of continuous operating showed that the maximum average temperatur

      The aim of this study is to investigate the response of the Ionospheric E- region critical frequency f_oE and virtual height h’E parameters to the solar cycle 22 over Baghdad city (latitude 33.3˚N, longitude 44.4˚E). Both parameters display a high relationship with the sunspot relative number within the ascending and descending phases of the solar cycle. The E - region response to the solar activity is obvious around noon, sunrise and sunset times. Moreover, the gap between local mid-afternoon, dawn and sunset values expands as solar activity rises. In the declining phase, there is an aspect that results in a peak of disturbance. This portion may have

Silver nanoparticles (AgNPs) were biosynthesized using the cell free supernatant of putative probiotic Lactobacillus paracasei A26. Several biological activities of biogenic AgNPs were investigated in respect to in vitro anti-oxidant and anti-tumor potentials.  Anti-oxidant potentials were screened in terms of free radical scavenging activity against two free radicals, 2, 2-Diphenyl-1-picrylhydrazyl (DPPH) and resazurin dye. AgNPs exhibited a potent scavenging activity against resazurin dye (91±0.046%) with an EC₅₀ concentration of 146.823 µg/ml, while scavenging of DPPH was significantly (P≤0.05) reduced to 72.330±0.114% using a higher EC₅₀ concentration of 176.12 µg/ml. The

For modeling a photovoltaic module, it is necessary to calculate the basic parameters which control the current-voltage characteristic curves, that is not provided by the manufacturer. Generally, for mono crystalline silicon module, the shunt resistance is generally high, and it is neglected in this model. In this study, three methods are presented for four parameters model. Explicit simplified method based on an analytical solution, slope method based on manufacturer data, and iterative method based on a numerical resolution. The results obtained for these methods were compared with experimental measured data. The iterative method was more accurate than the other two methods but more complexity. The average deviation of

A new mode of methodology was adopted in the assay of PM- HCL based on the use of water crystal gel bead made of poly acrylic acid in which the gel beads were left to absorbe persulphate solution that is necessary for the oxidation of PM- HCL in aqua media . The water crystal act as a reserviour for S2O82- . Optimum parameters were studied giving to specify the chemical and physical parameters. Two line manifold was used .The flow rates of 1.5 and 1.2 ml.min-1 was used , 3 gel beads , 120 μL sample volume , a linear dynamic range extend from 0.01- 18 mmol.L-1. A correlation coefficient (r) of 0.9991while the percentage linearity (r2%) of 99.82% with R.S.D% at 8 mmol.L-1 promethazine-HCl is less than 0.5% (ten replicates) and a detection