A winglet is devices attached at the wing tips, used to improve aircraft wing efficiency by reduction influence wing tips vortices and induct drag, increasing lift force at the wing tips and effective aspect ratio without adding greatly to the structural stress and weight in the wing structure. This paper is presented three-dimensional numerical analysis to proposed modification swept back wing by adding Raked winglets devices at the main wing tips belong the two seat trainer aircraft type Aermacchi Siai S211 by using Fluent ANSYS 13 software. CFD numerical analysis process was performed at the same flight boundary conditions indifferent wing angle of attacks with constant air flow velocity V∞ =50 (m/sec), ambient pressure Po=101325 (Pa), ambient temperature To=288.14 (K), and at air density ρo=1.225 (kg\m3) to both proposed wing model and the main aircraft wing model. The results are shown an improvement in aerodynamic parameters including increment lift coefficient to (0.22%-5.95%), reduction drag coefficient to (0.34% - 3.60%), increment wing load efficiency ratio to (2.62% - 7.30%), reduction induct drag coefficient CDi to (7.65% - 13.11%) compared with the main aircraft wing model and achieved an improvement in aircraft flight maneuver abilities and stability controls especially during descent, approach, landing and takeoff with lower speed with shortage runway.
Throughout this paper R represents a commutative ring with identity and all R-modules M are unitary left R-modules. In this work we introduce the notion of S-maximal submodules as a generalization of the class of maximal submodules, where a proper submodule N of an R-module M is called S-maximal, if whenever W is a semi essential submodule of M with N ? W ? M, implies that W = M. Various properties of an S-maximal submodule are considered, and we investigate some relationships between S-maximal submodules and some others related concepts such as almost maximal submodules and semimaximal submodules. Also, we study the behavior of S-maximal submodules in the class of multiplication modules. Farther more we give S-Jacobson radical of ri
... Show MoreFive samples of the ternary alloy Ge-S-Cd were created using the melting point method, and the effects of partially substituting cadmium for germanium were determined. and partial substitution of germanium by cadmium was used to study the change in electrical conductivity. Electrical experiments were performed on Ge35-xS65Cdxternary alloy with x = 0, 5, 10, 15, and 20. It was discovered that the conductivity (σdc) rises with rising temperature in all samples under experiment. This confirms that the samples have semiconductor behavior. It has been observed that there are three regions of electrical conductivity in the electrical conductivity curve at low, moderate, and high temperatures. The pr
... Show MoreIn this paper, a new class of ordinary differential equations is designed for some functions such as probability density function, cumulative distribution function, survival function and hazard function of power function distribution, these functions are used of the class under the study. The benefit of our work is that the equations ,which are generated from some probability distributions, are used to model and find the solutions of problems in our lives, and that the solutions of these equations are a solution to these problems, as the solutions of the equations under the study are the closest and the most reliable to reality. The existence and uniqueness of solutions the obtained equations in the current study are dis
... Show MorePricing has an important position among the elements of marketing mixture (4ps) as it represents revenues that in turn represent one of the important pillars' for resources affecting on organizations sustainability and development , and the failure in determining prices and their strategies has a dangerous effect on the organizations reality and future as a whole . from this point, this is what from the focus of the research problem,which centered on how to get companies to critical price that satisfies customers and achieve corporate objectives.
... Show MoreThe estimation of the parameters of linear regression is based on the usual Least Square method, as this method is based on the estimation of several basic assumptions. Therefore, the accuracy of estimating the parameters of the model depends on the validity of these hypotheses. The most successful technique was the robust estimation method which is minimizing maximum likelihood estimator (MM-estimator) that proved its efficiency in this purpose. However, the use of the model becomes unrealistic and one of these assumptions is the uniformity of the variance and the normal distribution of the error. These assumptions are not achievable in the case of studying a specific problem that may include complex data of more than one model. To
... Show MoreThroughout this paper R represents a commutative ring with identity and all R-modules M are unitary left R-modules. In this work we introduce the notion of S-maximal submodules as a generalization of the class of maximal submodules, where a proper submodule N of an R-module M is called S-maximal, if whenever W is a semi essential submodule of M with N ⊊ W ⊆ M, implies that W = M. Various properties of an S-maximal submodule are considered, and we investigate some relationships between S-maximal submodules and some others related concepts such as almost maximal submodules and semimaximal submodules. Also, we study the behavior of S-maximal submodules in the class of multiplication modules. Farther more we give S-Jacobson radical of rings
... Show MoreThe present paper deals with studying the effect of electrical discharge machining (EDM) and shot blast peening parameters on work piece fatigue lives using copper and graphite electrodes. Response surface methodology (RSM) and the design of experiment (DOE) were used to plan and design the experimental work matrices for two EDM groups of experiments using kerosene dielectric alone, while the second was treated by the shot blast peening processes after EDM machining. To verify the experimental results, the analysis of variance (ANOVA) was used to predict the EDM models for high carbon high chromium AISI D2 die steel. The work piece fatigue lives in terms of safety factors after EDM models were developed by FEM using ANSY
... Show MoreThe ground state densities of unstable neutron-rich 11Li and 12Be exotic nuclei are studied in the framework of the binary cluster model (BCM). The internal densities of the clusters are described by the single particle harmonic oscillator wave functions. The long tail performance is clearly noticed in the calculated neutron and matter density distributions of these nuclei. The structures of the two valence neutrons in 11Li and 12Be are found to be mixed configurations with dominant (1p1/2)2. Elastic electron scattering proton form factors for 11Li and 12Be are studied using the plane wave Born approximation (PWBA). It is found that the major difference between the calculated form factors of unstable nuclei [11Li, 12Be] and those of stab
... Show MoreThe present paper sheds light on irony as one of the most important and most common linguistic phenomena in modern linguistics, in general ,and in discourse in particular, whether it is (political, literary, journalistic, etc.). When irony is used correctly or positively, it paves the way for the speaker to gain the approval of other parties participating in the dialogue and dissolve barriers between them. It is a simple multi-functional linguistic style and an expression of one’s meaning by using language that normally signifies the opposite according to the context and the situation. Therefore, it is necessary to study its characteristics, define its functions and traces the extent of
... Show MoreAbstract The strategic performance of the United States depends on dealing with the Middle East countries and its variants on several bases and motives that enabled them to achieve American hegemony and invest its interests at the expense of the region countries. Within this performance, the administration of the United State President Donald Trump presented the Strategic Document on December 18, 2017, which focused on the principle of "America First", to determine the direction of future US strategic performance in the formulation of means of cooperation and intersections or hostility in addition to interests and threats.The future vision of the Arab region and the Middle East as a whole, this strategy is based on the fact that
... Show More