Cesarean section, which was introduced into clinical practice as a lifesaving procedure for both the mother and the baby, is one of the most common surgeries performed in modern obstetrics. Formerly it was performed in interest of the mother; currently it is frequently done for fetal indication. As other procedures of some complexity, its use follows the health care inequity pattern of the world; underuse in low income setting, and adequate or even unnecessary use in middle and high income setting (1).
The first modern cesarean section was performed by German gynecologist Ferdinand Adolf Kehrer in 1881. Cesarean section is often performed when a vaginal delivery would put the baby's or mother's life or health at risk. Many are also performed upon request (2).
Pregnancy and delivery are considered a normal physiological state in women; however, of all deliveries approximately 10% are considered high risk, some of which may require Cesarean section (3).
The cesarean delivery rate has increased throughout the world. Cesarean rates have increased over the past 40 years from approximately 5% to more than 30% in many industrialized countries (4). The cesarean rate is approximately 21.1% for the most developed regions of the globe, 14.3% for the less developed regions, and 2% for the least developed regions (5).
Recent studies reaffirm earlier recommendations of the world health organization (WHO), about optimal C-section rates, addressing that the best outcomes of mothers and babies appear to occur with C-section rates of 5% to 10%, while rates above 15% seem to do more harm than good (6).
In US the cesarean rate increased dramatically during the 1970s and early 1980s this may be accredited to the improved technology in detecting pre-birth distress, and began to decline in the late 1980s (based on data from the National Hospital Discharge Survey). Between 1989 and 1996 the total cesarean rate decreased as a result of a decrease in the primary rate and an increase in the rate of vaginal birth after Cesarean (VBAC). Since 1996, these trends have reversed, and increases have been rapid and sustained for primary and repeat Cesareans over the past decade (7).
According to the Iraq Multiple Indicator Cluster Survey 2006 (Iraq MICS 2006) (8), about 20% of births were delivered by C-section (Table 1). Moreover, a brief and rapid survey of C-sections in Baghdad Teaching Hospital, a tertiary referral hospital, indicated that the emergency C-sections account only for 62.2% of the total number of C-sections performed outside the working hours during April 2010 (9).
A study in the treatment and reuse of oily wastewater generated from the process of fuel oil treatment of gas turbine power plant was performed. The feasibility of using hollow fiber ultrafiltration (UF) membrane and nanofiltration (NF) membrane type polyamide thin-film composite in a pilot plant was investigated. Three different variables: pressure (0.5, 1, 1.5 and 2 bars), oil content (10, 20, 30 and 40 ppm), and temperature (15, 20, 30 and 40 ᵒC) were employed in the UF process while TDS was kept constant at 150 ppm. Four different variables: pressure (2, 3, 4 and 5 bar), oil content (2.5, 5, 7.5 and 10 ppm), total dissolved solids (TDS) (100, 200,300 and 400 ppm), and temperature (15, 20, 30 and 40 ᵒC) were manipulated with the h
... Show More
(3)
(2)
In this paper, we characterize normal composition operators induced by holomorphic self-map , when and .Moreover, we study other related classes of operators, and then we generalize these results to polynomials of degree n.
Submerged arc welding (SAW) process is an essential metal joining processes in industry. The quality of weld is a very important working aspect for the manufacturing and construction industries, the challenges are made optimal process environment. Design of experimental using Taguchi method (L9 orthogonal array (OA)) considering three SAW parameter are (welding current, arc voltage and welding speed) and three levels (300-350-400 Amp. , 32-36-40 V and 26-28-30 cm/min). The study was done on SAW process parameters on the mechanical properties of steel type comply with (ASTM A516 grade 70). Signal to Noise ratio (S/N) was computed to calculate the optimal process parameters. Percentage contributions of each parameter are validated by using an
... Show MoreBackground: Fractures of the humeral shaft
accounting for approximately 3% of all
fractures. There is a wide array of good
options for their treatment and controversy
over the best methods. Although good
techniques of osteosynthesis are available, the
aim of this article is toemphasize on the benefit
and good outcome of conservative treatment
for properly selected cases to decrease the cost
and avoid the complications of surgery.
The ceramic composite with different proportions of clay and silica was prepared with a grain size of 70 μm and the weight percentage was selected for four groups (clayx silica100-x) were x q15, 25, 30 and 50. In this manuscript, for each pressured sample, a sintering procedure was carried out for 3 hours under static air and at various sintering temperatures (1000, 1100, 1200, 1400)°C. After sintering, the density, porosity, water absorption, compression strength and thermal conductivity were measured. The best results were obtained using a mixture of 15% clay and 85% silica which were sintering at 1400°C for three hours under air.
This paper is summarized with one of the applications of adsorption behavior; A UV-Vis method has been applied to survey the isotherm of adsorption. Results for experimental showed the applicability of Langmuir equation. The effect of temperature on the adsorption of cobalt (II) Complex by bentonite surface was studied. The results shown that the amount of adsorption was formed to increase, such as the temperature increase (Endothermic process). Cobalt (II) Complex has adsorption studies by bentonite surface at different pH values (1.6-10); these studies displayed an increase in adsorption with increasing pH. ΔG, ΔH, and ΔS thermodynamic functions of the cobalt (II) Complex for their adsorption have been calculated.
(4)
(5)
In this article, performing and deriving te probability density function for Rayleigh distribution is done by using ordinary least squares estimator method and Rank set estimator method. Then creating interval for scale parameter of Rayleigh distribution. Anew method using is used for fuzzy scale parameter. After that creating the survival and hazard functions for two ranking functions are conducted to show which one is beast.
(5)
(2)
The ritual is a Sunnah between the two prostrations, not as some of the worshipers do, where he made it in the last tashahhud when the tasleematin, and it may be in the last tashahhud.
The assumption is Sunnah and most of the scholars say that in the middle tashahhud session as we have shown through research.
The Turks are Sunnah as well, and it is at the end of the prayer, whether it is double, triple or quadruple, whether it is naval or NAFTA, whether it is urban or travel, which is the view of most scholars from the three imams and others.
If we say weighting, say the audience of the three imams (Malik, Shafi'i, and Ahmad) is the most correct, and it is also the son of values, and if we say the choice is as Ibn Rushd said: by