In this work, the effect of vortex shedding on the solar collector performance of the parabolic trough solar collector (PTSC) was estimated experimentally. The effect of structure oscillations due to wind vortex shedding on solar collector performance degradation was estimated. The performance of PTSC is evaluated by using the useful heat gain and the thermal instantaneous efficiency. Experimental work to simulate the vortex shedding excitation was done. The useful heat gain and the thermal efficiency of the parabolic trough collector were calculated from experimental measurements with and without vortex loading. The prototype of the collector was fabricated for this purpose. The effect of vortex shedding at different operation condition

The subject of the listen to the voice of the customer of topics relatively new in management thought, as it won the attention of many organizations of different types, because it is important to achieve success and to continue and superiority to them, so there is a need to study this term in the Iraqi organizations and try to diagnose the implementation of the study sample to listen voice of the Customer and its

In the present study, MIG welding is carried out on low carbon steel type (AISI 1015) by using electrode ER308L of 1.5mm diameter with direct current straight polarity (DCSP). The joint geometry is of a single V-butt joint with one pass welding stroke for different plate thicknesses of 6, 8, and 10 mm. In welding experiments, AISI 1015 plates with dimensions of 200×100mm and edge angle of 60^o from both sides are utilized. In this work, three main parameters related to MIG welding process are investigated, which are welding current, welding speed, heat input and plate thickness, and to achieve that three groups of plates are employed each one consists of three plates. The results indicate that increasing the weld heat input (t

In this paper, a new equivalent lumped parameter model is proposed for describing the vibration of beams under the moving load effect. Also, an analytical formula for calculating such vibration for low-speed loads is presented. Furthermore, a MATLAB/Simulink model is introduced to give a simple and accurate solution that can be used to design beams subjected to any moving loads, i.e., loads of any magnitude and speed. In general, the proposed Simulink model can be used much easier than the alternative FEM software, which is usually used in designing such beams. The obtained results from the analytical formula and the proposed Simulink model were compared with those obtained from Ansys R19.0, and very good agreement has been shown. I

Frequency equations for rectangular plate model with and without the thermoelastic effect for the cases are: all edges are simply supported, all edges are clamped and two opposite edges are clamped others are simply supported.   These were obtained through direct method for simply supported ends using Hamilton’s principle with minimizing Ritz method to total energy (strain and kinetic) for the rest of the boundary conditions. The effect of restraining edges on the frequency and mode shape has been considered. Distributions temperatures have been considered as a uniform temperature the effect of developed thermal stresses due to restrictions of ends conditions on vibration characteristics   of a plate with different

Concrete pavements are essential to modern infrastructure, but their low tensile and flexural strengths can cause cracking and shrinkage. This study evaluates fiber reinforcement with steel and carbon fibers in various combinations to improve rigid pavement performance. Six concrete mixes were tested: a control mix with no fiber, a mix with 1% steel fiber (SF1%), a mix with 1% carbon fiber (CF1%), and three hybrid mixes with 1% fiber content: 0.75% steel /0.25% carbon fiber (SF0.75CF0.25), 0.25% steel /0.75% carbon fiber (SF0.25CF0.75), and 0.5% steel /0.5% carbon fiber ((SF0.5CF0.5). Laboratory experiments including compressive, flexural, and splitting tensile strength tests were conducted at 7, 28, and 90 days, while Finite Element Analys

This research discusses the developmental role of the social worker in providing care for children at risk. The research is desicriptive in nature include both the theoretical and field aspects. The theoretical aspect focuses on the characteristics and requirements of these children and what forms and implications are exposed to them by society, what is the developmental role of the social worker in the rehabilitation of this group. As for the field aspect, the study sample took a (40) social workers who working in Aiwa institutions inside Baghdad. A questionnaire of (14) questions was used as tool to collect the needed data.

يهدف البحث الحالي الى التعرف إلى درجة تقدير عينة من المديرين في المنظمات العامة لمستوى تطبيق ولتحقيق ، (Covid- نمط القيادة الخدمية من وجهة نظرهم ، وعلاقتها بمؤشر رضا الزبائن في ظل جائحة ( 19 ذلك اتبعت الباحثة المنهج التجريبي بتطبيق استبانة ضمت محورين، الأول: لقياس مستوى القيادة االخدمية وفقا الذي يشمل ( 8) أبعاد هي ( التمكين , الدعم , ( D. Van Dierendonck and I. Nuijten , لمقياس ( 2011 المساءلة, الشجاعة, التسامح , الموثوقية , التواضع , الر