In this work, we construct projectively distinct (k,3)-arcs in the projective plane PG(2,9) by applying a geometrical method. The cubic curves have been been constructed by using the general equation of the cubic. We found that there are complete (13,3)-arcs, complete (15,3)-arcs and we found that the only (16,3)-arcs lead to maximum completeness

    This article reveals the first record of the parasitoid wasp, Monodontomerus obscurus Westwood (Hymenoptera, Torymidae) from Iraq.  A total of 27 specimens were emerged from mud nests of sphecoid wasp of Sceliphron sp. (Hymenoptera, Sphecidae), that collected from a wall at a residential garden in Dohuk province.  A short morphological description is presented.

Osteoblast and osteoclast activity is disrupted in post-menopausal osteoporosis. Thus, to fully address this imbalance, therapies should reduce bone resorption and promote bone formation. Dietary factors such as phyto-oestrogens and Zn have beneficial effects on osteoblast and osteoclast activity. However, the effect of combinations of these factors has not been widely studied. We therefore examined the effect of coumestrol, daidzein and genistein in the presence or absence of zinc sulphate (Zn) on osteoclast and osteoblast activity. Osteoclast differentiation and bone resorption were significantly reduced by coumestrol (10- 7 m), daidzein (10- 5 m) and genistein (10- 7 m); and this direct anti-osteoclastic action was unaffected by Zn (10-

Experimental results on harmonic distortions in 13.56 MHz RF Argon glow discharge using different grounded electrodes areas and electrodes spacing are presented. The experiment is carried out at four pressure values. RF power values used are between 20 and 90 watts. The results indicate significant increase in distortions at two specific values of the cone angle enclosing the two electrodes within its geometrical volume. The computation of the cone head angle gave the symmetry discharge or asymmetry as well as when the angle is small the condition is near symmetry discharge associated with decrease in the nonlinearity.

Straight tendons in pretensioned members can cause high-tensile stresses in the concrete extreme fibers at end sections because of the absence of the bending stresses due to self-weight and superimposed loads and the dominance of the moment due to prestressing force alone. Accordingly, the concrete tensile stresses at the ends of a member prestressed with straight tendons may limit the service load capacity of the member. It is therefore important to establish limiting zone in the concrete section within which the prestressing force can be applied without causing tension in the extreme concrete fibers. Two practical methods are available to reduce the stresses at the end sections due to the prestressing force. The first method based

Recently new and multiple concepts emerged in the sustainability issues ,which transformed into number of planning and designing policies and strategies that must be committed by the designers and the relevant trends in building ,regarding Iraq and the reality of industrial areas ,especially in Baghdad, which helped to sustain few of it & emerged another with bad reflect ,which for that made it clear the importance of implicating sustainable ecological planning and designing strategies provided by the concept of Eco-industrial parks and the concept of Ecotowns and the future potentials provided ,and the easiness of carrying it out which made it flexible and away to provide a base supported by it for rebuilding and rehabilitation and

This paper compares between the direct and indirect georeferencing techniques in Photogrammetry bases on a simulation model. A flight plan is designed which consists of three strips with nine overlapped images for each strip by a (Canon 500D) digital camera with a resolution of 15 Mega Pixels.

The triangulation computations are carried out by using (ERDAS LPS) software, and the direct measurements are taken directly on the simulated model to substitute using GPS/INS in real case. Two computational tests have been implemented to evaluate the positional accuracy for the whole model and the Root Mean Square Error (RMSE) relating to (30) check points show that th

Reducing costs and protecting the environment surrounding economic unity has become the concern of many economic units and shifting their ideas towards preserving resources and protecting the environment by adopting strategies and techniques that take into account when applied reducing production costs and protecting the environment, including these strategies and techniques, the technical costs of the product life cycle and the strategy of cleaner production, as the application of the two concepts in local economic units helps to try to keep up with the countries that work to keep up with the success of their economic units by following the concepts that have been successful in  Developed countries by maintaining the sustainabilit