The Islamic Arts which include calligraphy and specifically the third line of the greatest
manifestation of Islamic civilization affair, and it was the mosques and mosques and holy
shrines scattered in the city of Baghdad, which had a deep impact in enhancing
communication
This means research study (third line aesthetics diversity of tactics in the architecture of
mosques) It is located in four seasons, which included the first chapter the research problem
represented by asking the following - :
-What are the methods of implementation of the third line in the architecture of mosques ?
And reflected the importance of research in it represents a serious attempt to investigate the
diversity in the organization design for linear configurations that promote communication
within and outside the mosques, mosques and holy sites located within the province of
Baghdad .
The objective of the study revealed the diversity of the methods implemented in the third line
Islamic mosques
The limits of the research has identified a third line configurations study varied within and
outside the corridors of mosques and mosques and holy sites of the era (2012 m -2013 m) and
their current, then seal chapter defines some of the terminology related to the subject matter ...
The second chapter goal of the theoretical framework and previous studies it was composed
of three sections define the first topic to address the third line study and aesthetic
characteristics .
The second topic was addressed by the researcher of the third line design spaces in the
building of mosques
The third chapter objective procedures for the research included the study population (42)
configuration in writing thuluth after excluding models repeated and similar and that Ataatuaq
with the objectives of the study or for other reasons, has chosen the researcher models sample
studied by the limited number (6) in a deliberate problem 20% of the Total community
researcher to study the original post after a group of experts with competence .
The samples were analyzed according to the sample analysis form that contributed to a lot of
experts .
The fourth chapter included the results of the study after an analysis and discussion of the
sample, which came the following - :
.1. Unity showed marked by the relationship with the other part, the part and the whole of
these relations is no doubt as to strengthen communication and raise satisfaction of sight at
the same time contribution in achieving the aesthetic diversity (sample models (
.2. Varied nature of the third line configurations implemented on the architectural elements in
the mosques and shrines between smooth and rough and Mabinhma diversity Mc contributes
largely to raise attention and enhance the aesthetic style within an area (sample models (
The conclusions that have chosen the most important researcher represented, including the
following - :
1.That each composition thuluth rhythm distinguishes whether free or regular or irregular,
uninteresting, or non-monotonic, or it may be a rhythm going because it expresses repeating
motor combines the unit and variable, one of the foundations of aesthetic overlay linear,
which has to be achieved in artwork
2.Calligrapher has maintained the consistency of parts of the characters with the college of the
Authority for the linear superposition of where (distance, height, and accuracy .(
And continue with the findings and conclusions of the recommendations and proposals
came then followed by a list of sources and supplements and then study researcher concluded
with a summary of research in the English language
Plane cubics curves may be classified up to isomorphism or projective equivalence. In this paper, the inequivalent elliptic cubic curves which are non-singular plane cubic curves have been classified projectively over the finite field of order nineteen, and determined if they are complete or incomplete as arcs of degree three. Also, the maximum size of a complete elliptic curve that can be constructed from each incomplete elliptic curve are given.
This paper deals with the nonlinear large-angle bending dynamic analysis of curved beams which investigated by modeling wave’s transmission along curved members. The approach depends on the wave propagation in one-dimensional structural element using the method of characteristics. The method of characteristics (MOC) is found to be a suitable method for idealizing the wave propagation inside structural systems. Timoshenko’s beam theory, which includes transverse shear deformation and rotary inertia effects, is adopted in the analysis. Only geometrical non-linearity is considered in this study and the material is assumed to be linearly elastic. Different boundary conditions and loading cases are examined.
From the results obtai
... Show MoreThe present investigation considers the effect of curing temperatures (30, 40, and 50˚C) and curing compound method on compressive strength development of high performance concrete, and compares the results with concrete cured at standard conditions and curing temperature (21˚C). The experimental results showed that at early ages, the rate of strength development at high curing temperature is greater than at lower curing temperature, the maximum increasing percentage in compressive strength is 10.83% at 50C˚ compared with 21C˚ in 7days curing age. However, at later ages, the strength achieved at higher curing temperature has been less, and the maximum percentage of reduction has been 5.70% at curing temperature 50C˚ compared with 21
... Show More
(1)
CuInSe2(CIS) thin films have been prepared by use vacuum thermal evaporation technique, of thickness750 nm with rate of deposition 1.8±0.1 nm/sec on glass substrate at room temperature and pressure (10-5) mbar. Heat treatment has been carried out in the range (400-600) K for all samples. The optical properties of the CIS thin films are been studied such as (absorption coefficient, refractive index, extinction coefficient, real and imaginary dielectric constant) by determined using Measurement absorption and transmission spectra. Results showed that through the optical constants we can make to control it are wide applications as an optoelectronic devices and photovoltaic applications.
We examine 10 hypothetical patients suffering from some of the symptoms of COVID 19 (modified) using topological concepts on topological spaces created from equality and similarity interactions and our information system. This is determined by the degree of accuracy obtained by weighing the value of the lower and upper figures. In practice, this approach has become clearer.
CuInSe2 (CIS)thin films have been prepared by use vacuum thermal evaporation technique, of 750 nm thickness, with rate of deposition 1.8±0.1 nm/sec on glass substrate at room temperature and pressure (10-5) mbar. Heat treatment has been carried out in the range (400-600) K for all samples. The optical properties of the CIS thin films are been studied such as (absorption coefficient, refractive index, extinction coefficient, real and imaginary dielectric constant)by determined using Measurement absorption and transmission spectra. Results showed that through the optical constants we can made to control it is wide applications as an optoelectronic devices and photovoltaic applications.
A theoretical study has been proposed to investigate the effects of different laser radiations (Nd - glass, DF and C02) as a heating source on different glass samples (Optical glass, Bk - 7 and Soda - lime glass) and different waves lengths (10.6, 3.8, 1.6) ???. The heat changes as which are resulted due irradiation with laser sources have been determined by using the one dimension mathematical relation as a function of time (t) and depth (z). The results of the study show ed that the irradiation with C02 laser had a greater effect than DF laser, while the effects of Nd - glass laser were minimal with a power density of (1.8*10?? w/m2) within atime(l^sec).(Forboth Kinds) The change in the temperatures were not exceeded than (70"K) in all sa
... Show More
(11)
(8)
Cobalt substituted nickel copper ferrite samples with general formula Ni0.95-xCoxCu0.05Fe2O4, where (x= 0.00, 0.01, 0.02, 0.03, 0.04 and 0.05) were prepared by solid-state reactions method at 1373 K for 4h. The samples prepared were examined by X-ray diffraction (XRD(, atomic force microscope (AFM), Fourier transform infra-red spectroscopy (FTIR) and Vickers hardness. X-ray diffraction patterns confirm the formation of a single phase of cubic spinel structure in all the prepared samples . XRD analysis showed that the increase in the cobalt concentration causes an increase in the lattice constant, bulk density (ρm) and the x-ray density (ρx), whereas porosity (p) and crystallite size (D) decrease. The Topography of the surface observed
... Show More
(1)