Background: The skull offers a high resistance of adverse environmental conditions over time, resulting in the greater stability of the dimorphic features as compared to other skeletal bony pieces. Sex determination of human skeletal considered an initial step in its identification. The present study is undertaken to evaluate the validity of 3D reconstructed computed tomographic images in sex differentiation by using craniometrical measurements at various parts of the skull. Materials and Method: 3D reconstructed computed tomographic scanning of 100 Iraqi subject, (50 males and 50 females) were analyzed with their age range from20-70 years old. Craniometrical linear measurements were located and marked on both side of the 3D skull images. Results: For the all parameters measured for sexes the mean value for Male had significantly greater than females with (p value < 0.001). A receiver operating characteristic curves was obtained for each variable to observe their overall performance in sex determination. The area of mastoid triangle was found the best variable in sex differentiation (ROC area =0.97 for unilateral skull measurements and 0.98 for bilateral measurements).while EU-EU was found to be the least one. Conclusion: 3D reconstructed Computed tomography scanning is a good diagnostic method for analyzing the craniometrical measurements of sex determination. sex differentiation for isolated part of the skull when only the fragmentary crania is available, could be achieved and the highest accuracy in sex determination can be obtained whether part or complete skull available.
(13)
(12)
In this study , Iraqi Bentonite clay was used as a filler for polyvinyl chloride polymer. Bentonite clay was prepared as a powder for some certain particle size ,followed by calcinations process at (300,700,900) OC ,then milled and sieved. The selected sizes were D ~75 µm and D ~150. After that polyvinyl Al-Cohool solution prepared and used as a coated layer covered the Bentonite powder before applied as a filler ,followed by drying , milling and sieving for limited recommend sizes. polyvinyl chloride solutions were prepared and adding of modified Bentonite power at certain quantities were followed .Sheet of these variables on the mechanical and thermal properties of the prepared reinforced particular polyvinyl chloride composite
... Show More
(98)
(92)
An experimental and numerical investigation of the effect of using two types of nanofluids with suspending of (Al2O3 and CuO) nanoparticles in deionized water with a volume fraction of (0.1% vol.), in addition to use three types of fin plate configurations of (smooth, perforated, and dimple plate) to study the heat transfer enhancement characteristics of commercial fin plate heat sink for cooling computer processing unit. All experimental tests under simulated conditions by using heat flux heater element with input power range of (5, 16, 35, 70, and 100 W). The experimental parameters calculated are such as water and nanofluid as coolant with Reynolds number of (7000, 8000, 9400 and 11300); the air
... Show More
(2)
The researcher has studied in his research (International Public Relations methods in building the state's image through Cyberspace)
, analytical study of the Facebook and twitter pages for British foreign office , the role was played by the International Public Relations in building the mental image of British , especially after the new media and internet have became influential role in political life . and became an important tools used by political institutions as ministries of foreign affairs in the twenty: one century .
The researcher identified the problem of this study with the following question:
(what is the role of the International Public Relations in building the mental image of state through Cyberspace)
To answer
(1)
(17)
(5)
The work reported in this study focusing on the abrasive wear behavior for three types of pipes used in oil industries (Carbone steel, Alloy steel and Stainless steel) using a wear apparatus for dry and wet tests, manufactured according to ASTM G65. Silica sand with
hardness (1000-1100) HV was used as abrasive material. The abrasive wear of these pipes has been measured experimentally by measuring the wear rate for each case under different sliding speeds, applied loads, and sand conditions (dry or wet). All tests have been conducted using sand of particle size (200-425) µm, ambient temperature of 34.5 °C and humidity 22% (Lab conditions).
The results show that the material loss due to abrasive wear increased monotonically with
(1)
This study can be considered as un introduction to the idioms and the strategy about the productive partnership development connection, that helps the researcher and the organization in their work in to activate development and the natural sources,manegment,to improve the two sides active connected to the local society, and to use it as easier and smoother participation of the people who work in development field and the natural sources management research, That connection depends mostly upon the capability of researcher and the development worker to increase the ability of individual and local society to specify and analyzing their problems and to try solutions to make their life better with good income.
The ceiling of the midbrain has a couple of optic lobes which are prominent and used as an optic center that reflex what it receives from eye retina fibers. The histology of optic tectum has been studied in Iraqi fish Barbus luteus (Heckel) . It was found that the number of optic tectum were six main strata organized from the outside to the inside as follows : the stratum marginal (SM), the stratum opticum (SO), the stratum fibrosum et griseum superficialis (SFGS), the stratum griseum central (SGC), the stratum album central (SAC), the stratum periventricular (SPV), . the tow last strata consider deep layers on the optic tectum. It was noticed that the superficial strata was the first (SM), while the thickest strata was the four (SGC), whic
... Show More