Background: The association between facial types and dental arches forms has considerable implications in orthodontic diagnosis and treatment planning. The aim was to establish the maxillary and mandibular dental arches width and length in skeletal and dental class II division 1 and class III malocclusion groups, find out the most frequent dental arch form and facial type and the association between them and to check the gender differences. Materials and Methods: Frontal and lateral facial photographs and maxillary and mandibular occlussal photographs for 90 iraqi subjects with age 18-25 years old (45 males and 45 females) divided equally into three groups, the 1st group with class II division 1malocclusion (overjet more than 3mm but less than or equal to 6mm), the 2nd group with class II division 1malocclusion (overjet more than 6mm) while the 3rd group with class III malocclusion (edge to edge or reverse overjet).Six linear measurements for each maxillary and mandibular dental cast photographs and two liner measurements for frontal and profile facial photographs was analyzed with (AUTO CAD 2013), which simplified the analyzing process and reduced the time and effort spent on taking measurements directly from the records to facilitate work and to gain more accurate results. Results: All the mean value of dental arches and facial measurements were higher in male than female, the most frequent maxillary and mandibular dental arch form in the three groups was the mid arch form follow by the narrow then the wide arch form except in the mandibular dental arch of the 3rd group it follow by the wide then the narrow arch form.The most frequent facial type in the 1st group is the Mesoprosopic one,followed by the Leptoprosopic then the Euryprosopic face type while in the 2nd and 3rd group the most frequent facial type is the Leptoprosopic, follow by the Mesoprosopic then the Euryprosopic facial type. An association was found between mid arch form and the Mesoprosopic face type in the 1st group, while no clear association was found between dental arch form and facial type in the 2nd and 3rd group for both genders. Conclusions: It was concluded that there was an association between facial type and dental arch form in subject with class II division 1malocclusion (overjet not more than 6mm), while in subject with class II division 1malocclusion (overjet more than 6mm) or with class III malocclusion (edge to edge or reverse overjet) no clear association was found between dental arch form and facial type.
The research aims at clarifying the relationship between innovative marketing skills and broad recommendation as a vital and important issue for organizations in general and service organizations in particular to demonstrate how innovative marketing skills contribute to broad adoption and to determine the relationship between interdependence and the impact of innovative marketing skills on the broad recommendation. Some questions are posed by the research problem. Is there a clear awareness among individuals in the company about the concept of marketing marketing skills and how do innovative marketing skills affect the broad recommendation of the surveyed company? How innovative marketing skills relate to the broad recommendation
... Show More
In this work, silicon nitride (Si3N4) thin films were deposited on metallic substrates (aluminium and titanium sheets) by the DC reactive sputtering technique using two different silicon targets (n-type and p-type Si wafers) as well as two Ar:N2 gas mixing ratios (50:50 and 70:30). The electrical conductivity of the metallic (aluminium and titanium) substrates was measured before and after the deposition of silicon nitride thin films on both surfaces of the substrates. The results obtained from this work showed that the deposited films, in general, reduced the electrical conductivity of the substrates, and the thin films prepared from n-type silicon targets using a 50:50 mixing ratio and deposited on both
... Show More
(23)
(5)
This study was undertaken to diagnose routine settling problems within a third-party oil and gas companies’ Mono-Ethylene Glycol (MEG) regeneration system. Two primary issues were identified including; a) low particle size (<40 μm) resulting in poor settlement within high viscosity MEG solution and b) exposure to hydrocarbon condensate causing modification of particle surface properties through oil-wetting of the particle surface. Analysis of oil-wetted quartz and iron carbonate (FeCO₃) settlement behavior found a greater tendency to remain suspended in the solution and be removed in the rich MEG effluent stream or to strongly float and accumulate at the liquid-vapor interface in comparison to naturally water-wetted particles. As su
... Show More
(13)
(13)
In order to improve the effectiveness, increase the life cycle, and avoid the blade structural failure of wind turbines, the blades need to be perfectly designed. Knowing the flow angle and the geometric characteristics of the blade is necessary to calculate the values of the induction factors (axial and tangential), which are the basis of the Blade Element Momentum theory (BEM). The aforementioned equations form an implicit and nonlinear system. Consequently, a straightforward iterative solution process can be used to solve this problem. A theoretical study of the aerodynamic performance of a horizontal-axis wind turbine blade was introduced using the BEM. The main objective of the current work is to examine the wind turbine blade’s perf
... Show More
(1)
(2)
The paper uses the Direct Synthesis (DS) method for tuning the Proportional Integral Derivative (PID) controller for controlling the DC servo motor. Two algorithms are presented for enhancing the performance of the suggested PID controller. These algorithms are Back-Propagation Neural Network and Particle Swarm Optimization (PSO). The performance and characteristics of DC servo motor are explained. The simulation results that obtained by using Matlab program show that the steady state error is eliminated with shorter adjusted time when using these algorithms with PID controller. A comparative between the two algorithms are described in this paper to show their effectiveness, which is found that the PSO algorithm gives be
... Show MoreThe purpose of this study was to determine the influence of environmental pH on production of biofilms and virulence genes expression in Pseudomonas aeruginosa.
Among 303 clinical and environmental samples 109 (61 + 48) isolates were identified as clinical and environmental P. aeruginosa isolates, respectively. Clinical samples were obtained from patients in the Al-Yarmouk hospital in Baghdad city, Iraq. Waste water from Al-Yarmouk hospital was used from site before treatment unit to collect environmental samples. The ability of prod