Background׃ Halitosis is a common condition and is most often caused by a buildup of bacteria in the mouth because of gum disease, food, or plaque. It can result in anxiety among those affected, it is also associated with depression and symptoms of obsessive compulsive disorder. The aim of this study isto assess the prevalence of self-reported halitosis and associated factors (dental plaque, gingival condition and dental caries) in 15 years old male students in Karbala city in Iraq. Additionally, we studied adolescents’ concern with their own breath and whether anyone had ever told them that they had halitosis. Methods׃ A cross sectional observational survey was conducted to15 years old high school students from public and private schools in the city of Karbala, Iraq. The random sample consisted of 400 adolescents from 44 schools. An interview with a structured questionnaire was administered along with measurement of oral parameters (PI, GI, DMF). Results׃ The prevalence of self-reported halitosis was 48.50% according to question one. Prevalence of halitosis according to total score of questionnaire was 86.5%. 13.5% reported that they didn’t have halitosis. It is concluded that there is high prevalence of self-reported halitosis, which is associated with a socioeconomic pattern. Most adolescents report concern with their own breath. Dental plaque and gingival status are associated significantly with self-reported halitosis. The high prevalence of self-reported halitosis according to questionnaire among the students may be due to the consumption of garlic or spicy food, in addition dental plaque, gingivitis and dental caries cause increase in volatile silver compound level which cause increase in halitosis. Conclusion׃ Self-reported halitosis is a prevalent situation in about 50% of adolescents in Karbala city. Patients’ self-reported halitosis is found to be associated with dental plaque, gingivitis and dental caries.
Artificial lift techniques are a highly effective solution to aid the deterioration of the production especially for mature oil fields, gas lift is one of the oldest and most applied artificial lift methods especially for large oil fields, the gas that is required for injection is quite scarce and expensive resource, optimally allocating the injection rate in each well is a high importance task and not easily applicable. Conventional methods faced some major problems in solving this problem in a network with large number of wells, multi-constrains, multi-objectives, and limited amount of gas. This paper focuses on utilizing the Genetic Algorithm (GA) as a gas lift optimization algorit
In this work, silicon nitride (Si3N4) thin films were deposited on metallic substrates (aluminium and titanium sheets) by the DC reactive sputtering technique using two different silicon targets (n-type and p-type Si wafers) as well as two Ar:N2 gas mixing ratios (50:50 and 70:30). The electrical conductivity of the metallic (aluminium and titanium) substrates was measured before and after the deposition of silicon nitride thin films on both surfaces of the substrates. The results obtained from this work showed that the deposited films, in general, reduced the electrical conductivity of the substrates, and the thin films prepared from n-type silicon targets using a 50:50 mixing ratio and deposited on both
... Show MoreThis study was undertaken to diagnose routine settling problems within a third-party oil and gas companies’ Mono-Ethylene Glycol (MEG) regeneration system. Two primary issues were identified including; a) low particle size (<40 μm) resulting in poor settlement within high viscosity MEG solution and b) exposure to hydrocarbon condensate causing modification of particle surface properties through oil-wetting of the particle surface. Analysis of oil-wetted quartz and iron carbonate (FeCO₃) settlement behavior found a greater tendency to remain suspended in the solution and be removed in the rich MEG effluent stream or to strongly float and accumulate at the liquid-vapor interface in comparison to naturally water-wetted particles. As su
... Show MoreIn order to improve the effectiveness, increase the life cycle, and avoid the blade structural failure of wind turbines, the blades need to be perfectly designed. Knowing the flow angle and the geometric characteristics of the blade is necessary to calculate the values of the induction factors (axial and tangential), which are the basis of the Blade Element Momentum theory (BEM). The aforementioned equations form an implicit and nonlinear system. Consequently, a straightforward iterative solution process can be used to solve this problem. A theoretical study of the aerodynamic performance of a horizontal-axis wind turbine blade was introduced using the BEM. The main objective of the current work is to examine the wind turbine blade’s perf
... Show MoreThe Weibull distribution is considered one of the Type-I Generalized Extreme Value (GEV) distribution, and it plays a crucial role in modeling extreme events in various fields, such as hydrology, finance, and environmental sciences. Bayesian methods play a strong, decisive role in estimating the parameters of the GEV distribution due to their ability to incorporate prior knowledge and handle small sample sizes effectively. In this research, we compare several shrinkage Bayesian estimation methods based on the squared error and the linear exponential loss functions. They were adopted and compared by the Monte Carlo simulation method. The performance of these methods is assessed based on their accuracy and computational efficiency in estimati
... Show MoreThis article presents the results of an experimental investigation of using carbon fiber–reinforced polymer sheets to enhance the behavior of reinforced concrete deep beams with large web openings in shear spans. A set of 18 specimens were fabricated and tested up to a failure to evaluate the structural performance in terms of cracking, deformation, and load-carrying capacity. All tested specimens were with 1500-mm length, 500-mm cross-sectional deep, and 150-mm wide. Parameters that studied were opening size, opening location, and the strengthening factor. Two deep beams were implemented as control specimens without opening and without strengthening. Eight deep beams were fabricated with openings but without strengthening, while
... Show More