Background: The displacement of artificial teeth during complete denture construction presents major processing errors in the occlusal vertical dimension which were verified at the previous trial denture stage. The aim of this study was to assess the effect of delay in processing after final flask closure and tension application on the vertical acrylic and porcelain teeth displacement of complete dentures constructed from heat cured acrylic and the results were compared with the conventional processing method. Materials and methods: forty samples of identical maxillary complete dentures were constructed from heat polymerized acrylic resin. These samples were subdivided into the following experimental subgroups in which each subgroup contains 5 samples for both acrylic and porcelain teeth and as follows: 1. Conventional flasking technique and immediate processing. 2. Conventional flasking technique and 6 hours delay in processing. 3. flasking technique with tension system and immediate processing. 4. flasking technique with tension system and 6 hours delay in processing. Reference metal pins were attached to the middle of the buccal surface of the upper right canine and center of the buccal groove of the left first molar. And according to these reference points on the teeth another metallic Reference pins were fixed on the denture vestibules and at a distance of 7.5mm by straight lines and 6.5mm where placed between the metal pins and the vestibules in order to standardize the measurement. The distance between the right and left metal pins on the canine and molars and the corresponding metal pins on the buccal vestibules were measured during the wax up stage and after processing by using an optical travelling microscope with an accuracy of 0.0005 mm. Means in (mm) were analyzed statistically by analysis of variance and the comparative T-test and least significance test (LSD). Results: Significant reduction in vertical displacement of the teeth occurred in groups when 6 hours delay in processing were applied, but a significant improvement was also observed in groups with tension system application when compared with control group. On the other hand, there were a high significant reduction in the vertical displacement in groups with tension system and 6 hours delay in processing combination. While for the type of artificial teeth data showed significant difference in the amount of vertical displacement of the teeth in groups with acrylic teeth when compared with porcelain teeth. Conclusions: The findings of this study showed that 6 hours delay in processing and tension system application were effective in reducing the vertical displacement of the artificial teeth during flasking. The maximum reduction in the displacement was observed in dentures constructed from acrylic teeth. On the other hand, significant decrease in vertical displacement of the teeth was detected in dentures constructed from porcelain teeth.
In the postmodern era, the graphic design styles showed a new visualization method when the graphic designers had changed the traditional conditions by using design elements with new technics for photos, collage and comics illustration. The researcher assumes that the graphic design styles were affected by the art's movement at that period throw the same perspective of view for the concept presented in the art pieces and their entire message. Therefore, the researcher chooses field was the period of 1945-1970 in the USA for the (pop-art and conceptual-art) and explored the main visual effects that expressed the visual dialogue and compared them with the most common design styles ant the same period and location, the results of selected e
... Show More
The choice of gate dielectric materials is fundamental for organic field effect transistors (OFET), integrated circuits, and several electronic applications. The operation of the OFET depends on two essential parameters: the insulation between the semiconductor layer and the gate electrode and the capacitance of the insulator. In this work, the electrical behavior of a pentacene-based OFET with a top contact / bottom gate was studied. Organic polyvinyl alcohol (PVA) and inorganic hafnium oxide (HfO2) were chosen as gate dielectric materials to lower the operation voltage to achieve the next generation of electronic applications. In this study, the performance of the OFET was studied using monolayer and bilayer gate insulators.
... Show More
(377)
(354)
In low-latitude areas less than 10° in latitude angle, the solar radiation that goes into the solar still increases as the cover slope approaches the latitude angle. However, the amount of water that is condensed and then falls toward the solar-still basin is also increased in this case. Consequently, the solar yield still is significantly decreased, and the accuracy of the prediction method is affected. This reduction in the yield and the accuracy of the prediction method is inversely proportional to the time in which the condensed water stays on the inner side of the condensing cover without collection because more drops will fall down into the basin of the solar-still. Different numbers of scraper motions per hour (NSM), that is
... Show More
(7)
(6)
(2)
(1)
ABSTRACT
The research aims to identify the role of scientific planning of inventory by determining the quantity of economic demand and the number of times of purchase and associated annual total costs to achieve a sufficient and appropriate level of inventory . The research was based on the case study methodology. Materials of increasing demand in the Institute of Technical Management and knowledge of the degree of conformity of the procurement plan with the standard indicators adopted in a scientific method ,its include economic order quantity and number of purchasing times .
one of The main results of the research was the existence of a large difference between the quantity of the economic purchase of ea
(1)
This research attempts to shed light on a topic that is considered one of the most important topics of HRMs management, which is the Employee centric approach by examining its philosophy and understanding . To achieve the goal, the research relied on the philosophical analytical method, which is one of the approaches used in theoretical studies. The research reached a set of conclusions, the most important of which are the theoretical studies that addressed this entry in the English language and the lack of it in the Arabic language, according to the researcher's knowledge. The research reached a set of recommendations, the most important of which was that this approach needs more research, analysis and study at the practical and th
... Show More
The Video effect on Youths Value
This paper is mainly concerned with the study of the moral aspects that prompts William Shakespeare to attempt a romance in which he has embedded the epitome of his thought, experience, and philosophy concerning certain significant aspects of human life whose absence or negligence may threaten human existence, peace, and stability. From the beginning of history man realizes the importance of prosperity on the many and various levels that touch and address his needs and desires—natural, material, and spiritual. The Tempest, due to the dramatist's awareness of the aforementioned values, reflects the dramatist's duty as to projecting and unfolding these important aspects, rec
... Show More