Tillage appearance device is mechanical, electric-electronic design, getting Patent from the Central Organization for Standardization and Quality Control – Industrial Property Department - Ministry of Planning – The Republic of IRAQ under number Patent 3876 in 20 / 4 / 2014, calculates the number of clods per area by Tillage appearance device, This is done through the generation electrical impulses are sent to the controlled accurate calculates number clods required space and shows the result on the screen in order to see the tillage view per area. Three factor used in these experiment, first factor represents forward speed of tractor three levels (3.5, 4.5, and 5.5 km/h), second factor represent soil moisture content at two levels (14 – 17 and 17- 20 %) and third factor was depth of tillage at three levels (10 ,15 and 20 cm) in texture silt clay loam in Wasit cityIraq. Split – split plot design under randomized complete block design with three replications and Least Significant Design 5 % was used to compare the between means of treatments. The result showed that significant differences to forward speed to the tractor on tillage appearance of more than 10 cm. Speed 5.5 km/h recorded lower number of clods 10 cm 6.5230 clods/m2. Also result showed that the increase soil moisture content from 14-17 to 17-20 % led to increase the tillage appearance more than 10 cm from 7.5178 to 9.6200 clods/m2 for tillage appearance device respectively ,while the conventional method recorded 9.1639 to 9.9400 clods/m2. Observed also depth of tillage 10 cm for the least number of clods soil more 10 cm were 6.753,6.9633 clods/m2 when used the tillage view device and conventional method respectively. There was a significant correlation between the reading of the tillage appearance device and conventional methods which means that the reading device was Accuracy.
According to grammarians In ( نإ) and Itha (اذإ) are conditionals and sometimes they may be used interchangeably. However, when they are mentioned in the Holy Qur’an, they have their own specific use. This paper attempts to investigate their meanings in the source language as well as investigate their translations and find out any differences or similarities. The translations that are adopted in this research are as follows: Pickthall, Al-Hilali & Khan, and Shakir.
Tannin acyl hydrolase as the common name of tannase is an inducible extracellular enzyme that causes the hydrolysis of galloyl ester and depside bonds in tannins, yielding gallic acid and glucose. The main objective of this study is to find a novel gallic acid and tannase produced by
Now-a-days the Flexible AC Transmission Systems (FACTS) technology is very effective in improving the power flow along the transmission lines and makes the power system more flexible and controllable. This paper deals with the most robust type of FACTS devices; it’s a Unified Power Flow Controller (UPFC). Many cases have been taken to study how the system behaves in the presence and absence of the UPFC under normal and contingency conditions. The UPFC is a device that can be used to improve the bus voltage, increasing the loadability of the line and reduce the active and reactive power losses in the transmission lines, through controlling the flow of real and reactive power. Both the magnitude and the phase angle of th
... Show MoreConcrete columns with hollow-core sections find widespread application owing to their excellent structural efficiency and efficient material utilization. However, corrosion poses a challenge in concrete buildings with steel reinforcement. This paper explores the possibility of using glass fiber-reinforced polymer (GFRP) reinforcement as a non-corrosive and economically viable substitute for steel reinforcement in short square hollow concrete columns. Twelve hollow short columns were meticulously prepared in the laboratory experiments and subjected to pure axial compressive loads until failure. All columns featured a hollow square section with exterior dimensions of (180 × 180) mm and 900 mm height. The columns were categorized into
... Show MoreThe research focuses on addressing one of the most important concepts of modern management that deal with the relationship between government institutions and stakeholders, Which now occupies a special significance in trends modern management, a concept of corporate governance it takes the internal mechanisms due to its key role and is important in the process of corporate governance and looking for building Effective mechanisms for this concept in light of laws and regulations that are available in the local environment and on the functioning of government institutions, Search has been applied in the Federal Board of Supreme Audit of Iraq (BSA) due to its particular importance as an institution control and as a awaits the societ
... Show MoreAt a time when the general rules in the different legal systems require the presence of two parties to the contract, one of which is issued the first expression of the will and is called the offer, and the other is issued from the other and is called the acceptance. A special type of contracts emerged in the beginning of the last century called the “unilateral contracts”. The side sparked a major jurisprudential dispute, as well as the issuance of several contradictory judicial rulings on it. Hence, this research came to highlight this special type of contract. Key words: the definition of a unilateral contract, its distinction from other legal situations, and its effects.
Tillage tools are subject to friction and low-stress abrasive wear processes with the potential deterioration of the desired soil quality, loss of mechanical weed efficacy, and downtime for replacing worn tools. Limited experimental methods exist to quantify investigate the effect of wear-resistant coatings on shape parameters of soil-engaging tools. ASTM standard sand/rubber wheel abrasion and pin-on-disk tests are not able to simulate wear characteristics of the complex shape of the tillage tools. Even though the tribology of tillage tools can be realistic from field tests, tillage wear tests under field conditions are expensive and often challenging to generate repeatable engineeri