Objectives: Assessment outcome of DOTS (Directly observed therapy short course) program in Al-Sader City
Sector that was established by the WHO.
Methodology: Three cohorts groups of patients attending Baghdad TB institute and TB center in Al-Sader city
were followed retrospectively. The 1st cohort included (314) patients registered in year (2003), the 2nd cohort
included (327) patients registered in year (2004), the 3rd cohort included (321) patients registered in year
(2005). The collected data were analyzed for case detection, treatment outcomes, retreatment outcomes,
treatment success, and retreatment success in regard to time, age and sex.
Results: The following rates were extracted for the three cohort: Case detection rate within 1st, 2nd, and 3rd
cohort were (73.36%, 64.24%, and 71.49% respectively).Treatment outcomes (cured, completed treatment,
defaulters, treatment failure, died and transfer out) of new smear positive patients within the 1st, 2nd and 3rd
were (71.7%, 12.7%, 10.2%, 3.5%, 1%, 1%), (64.8%, 19.9%, 0.9%, 7%, 0.6%, 6.7%) and (61.4%, 24%, 3.1%, 5.9%,
0.6%, 5% respectively).Retreatment outcomes (cured, completed treatment, defaulters, treatment failure, died
and transfer out) within 1st, 2nd and 3rd cohort were (55.6%, 7.9%, 6.6%, 15.2%, 4%, 10.6%), (44.9%, 7.7%,
2.6%, 21.8%, 4.5%, 18.6%) and (41.8%, 14.6%, 11.4%, 19.6%, 1.9%, 10.8% respectively. Treatment success rate
within the 1st, 2nd and 3rd cohort were (84.39%, 84.7%, and 85.35%) respectively. Retreatment success rate
within the 1st, 2nd and 3rd cohort was (63.57%, 52.56%, and 56.32%) respectively.
Recommendation :Increase case detection rate through increase health awareness to the community about
the mode of transmission and risk of TB disease, Increase the training of health team so that they can follow up
of patients at home, Increase follows up of defaulters to be able to deal with them and a study for relapses
cases is recommended
The presence of residual antibiotics in water results in the development of antibiotics resistant genes. The available wastewater treatment systems are not capable of removing such antibiotics from sewage. Thus, antibiotics need to be removed before the discharge of wastewater. Adsorption is among the promising techniques for the wastewater treatment to aid the removal of a wide range of organic and inorganic pollutants. The present work is a contribution to the search for an economical method for the removal of low concentrations of amoxicillin (AMX) from water by adsorption on water treatment residue, WTR, taken from a local drinking water facility. The chemical composition and the adsorptive characteristics of the material were first
... Show More
(25)
(21)
(6)
(6)
(8)
The aim of the present research is to investigate the effecting of pH parameter on the feasibility of lead removal from simulated wastewater using an electrochemical system. Electrocoagulation method is one of electrochemical technology which is used widely to treat industrial wastewater. Parameters affecting this operation, such as initial metal concentration, applied current, stirrer speed, and contact time of electroprocessing were taken as 155ppm, 1.5 Ampere, 150 rpm, 60 minutes respectively. While pH of the simulated wastewater was in the range of 2 to 12 in the experiments. It was found from the results that pH is an important parameter affecting lead removal operation. The best value of pH parameter is appro
... Show More
(22)
(18)
The removal of COD from wastewater generated by petroleum refinery has been investigated by adopting electrocoagulation (EC) combined with adsorption using activated carbon (AC) derived from avocado seeds. The process variables influencing COD removal were studied: current density (2–10 mA/cm2), pH (4–9), and AC dosage (0.2–1 g/L). Response surface methodology (RSM) based on Box–Behnken design (BBD) was used to construct a mathematical model of the EC/AC process. Results showed that current density has the major effect on the COD removal with a percent of contribution 32.78% followed by pH while AC dosage has not a remarkable effect due to the good characteristics of AC derived from avocado seeds. Increasing current density gives be
... Show More
(6)
(6)
(7)
(5)
This paper was aimed to study the efficiency of forward osmosis (FO) process as a new application for the treatment of wastewater from textile effluent and the factors affecting the performance of forward osmosis process.
The draw solutions used were magnesium chloride (MgCl2), and aluminum sulphate (Al2 ( SO4)3 .18 H2O), and the feed solutions used were reactive red, and disperse blue dyes.
Experimental work were includes operating the forward osmosis process using thin film composite (TFC) membrane as flat sheet for different draw solutions and feed solutions. The operating parameters studied were : draw solutions concentration (10 – 90 g/l), feed solutions concentration (5 – 30 mg/l), draw solutions flow rate (10 – 50 l/hr
(3)
(8)
(9)
Objective: To identification environmental and psychological violence's components among collegians’ students of different stages, and gender throughout creating specific questionnaire, and estimating regression of environmental domain effect on psychological domain, as well as measuring powerful of the association contingency between violence's domains in admixed form with respondent characteristics, such that (Demographics, Economics, and Behaviors), and extracting model of estimates impact of studied domains in studying risks, and protective factors among collegians’ students in Baghdad city. Methodolog
In this investigation, metal matrix composites (MMCs) were manufactured by using powder technology. Aluminum 6061 is reinforced with two different ceramics particles (SiC and B4C) with different volume fractions as (3, 6, 9 and 12 wt. %). The most important applications of particulate reinforcement of aluminum matrix are: Pistons, Connecting rods etc. The specimens were prepared by using aluminum powder with 150 µm in particle size and SiC, B4C powder with 200 µm in particle size. The chosen powders were mixed by using planetary mixing setup at 250 rpm for 4hr.with zinc stearate as an activator material in steel ball milling. After mixing process the powders were compacted by hydraulic
... Show More