Genetic variation was studied in 22 local and imported samples collected from local Iraqi market by using random amplified polymorphic DNA (RAPD-PCR). Five randomly primers set were used in this study. These primers produced 292 bands. Molecular weights of these bands ranged between 1.8 Kb (1800 bp) to 150 bp. The percentage of polymorphic bands is 100%, with one distinguished band which is produced by using C52 primer. The other primers did not produce any distinguished band. The results of Dendrogram of the studied samples depended on RAPD-PCR results by using Jaccard coefficient for genetic similarity was distributed the samples into 8 groups. This Dendrogram revealed a higher similarity between Iraqi/Yousifia green bell pepper and Jo

            Environmentally friendly copper oxide nanoparticles (CuO NPs) were prepared with a green synthesis route via Anchusa strigosa L.  Flowers extract. These nanoparticles were further characterized by FTIR, XRD and SEM techniques. Removing of Gongo red from water was applied successfully by using synthesized CuO NPs which used as an adsorbent material. It was validated that the CuO NPs eliminate Congo red by means of adsorption, and the best efficiency of adsorption was gained at pH (3). The maximum adsorption capacity of CuO NPs for Congo red was observed at (35) mg/g. The equilibrium information for adsorption have been outfitted to the Langmuir, Freundlich, Temkin and Halsey adsorption isot

Friction Stir Welding (FSW) is one of the most effective solid states joining process and has numerous potential applications in many industries. A FSW numerical tool, based on ANSYS F.E software, has been developed. The amount of the heat gone to the tool dictates the life of the tool and the capability of the tool to produce a good processed zone. Hence, understanding the heat transfer aspect of the friction stir welding is extremely important for improving the process. Many research works were carried out to simulate the friction stir welding using various softwares to determine the temperature distribution for a given set of welding conditions. The objective of this research is to develop a finite element sim

With the increasing intensity of the ecological and environmental problems and the scarcity of fresh water, this paper was introduced to investigate the ability to use treated wastewater as a cooling media via studying its behavior throughout a cooling tower. The simultaneous transfer of heat and mass from the treated wastewater to air over splash-fill packing arranged in a zigzag manner was studied. The characteristic of the cooling tower, the outlet water temperature, and the rejected heat were investigated as the water-to-air ratio and inlet water temperature were varied. The core results show that the cooling tower of the tower decreases with increasing water-to-air ratio, and increases with the raise of inlet water temperature.

The In this experimental study, natural stone powder was utilized to improve a cohesive soil’s compaction and strength properties. According to the significant availability of limestone in the globe, it has been chosen for the purpose of the study, in addition to considering the existing rock industry massive waste. Stone powder was used in percentages of 4, 8, 12, 16% replaced from the soil weight in dry state. Some of cohesive soil’s consistency, shear, and compaction properties were depicted after improvement. The outcomes yielded in significant amendments in the experimented geotechnical properties after stone powder addition considering 60 days curing period. Cohesion and friction angle were notably increased by

This paper presents experimentally a new configuration of shear connector for Steel-Concrete-Steel (SCS) sandwich beams that is derived from truss configuration. It consists of vertical and inclined shear connectors welded together and to cover steel plates infilled with concrete. Nine simply supported SCS beams were tested until the failure under a concentrated central load (three- point bending). The beams were similar in length (1100mm), width (100mm), and the top plate thickness (4mm). The test parameters were; beam thickness (150, 200, 250, and 300mm), the bottom plate thickness (4, and 6mm), the diameter of the shear connectors (10, 12, and 16mm), and the connector spacing (100, 200, and 250mm). The test results sh

Focusing of Gaussian laser beam through nonlinear media can induce spatial self- phase modulation which forms a far field intensity pattern of concentric rings. The nonlinear refractive index change of material depends on the number of pattern rings. In this paper, a formation of tunable nonlinear refractive index change of hybrid functionalized carbon nanotubes/silver nanoparticles acetone suspensions (F-MWCNTs/Ag-NPs) at weight mixing ratio of 1:3 and volume fraction of 6x10-6 , 9x10-6 , and 18x10-6 using laser beam at wavelength of 473nm was investigated experimentally. The results showed that tunable nonlinear refractive indices were obtained and increasing of incident laser power density led to increase the nonlinear refractive inde

  In this research study, I tried to trace the epic effect to learn how it was understood and how it was used. Following the descriptive and analytical approach in the research, the first chapter dealt with a presentation of the methodological framework of the problem, the goal, the limits of the research, the importance and the need for it and the definition of terms, as well as the theoretical framework which consisted of two topics, including the impact of the epic theater on the world theater and the second the effect of the epic theater on the Arab theater, This came by tracing the epic impact on the world stage of the Greeks, the Middle Ages, the Renaissance, and the Arab theater of the twentieth century.
As for the second

Abstract

The study aims to know the degree of secondary school managers' practice of servant leadership in Gaza from their teachers’ perspective. It further aims to examine whether there are any statistically significant differences at (α 0.05≥) between the means of the study sample’s members attributed to variables such as (gender, educational qualification, and years of experience). To achieve the objectives of the study, the study adopted the descriptive survey method, using a questionnaire consisting of (30) items distributed to four domains: (workers service, ethical dealing, motivation & influence, and building an organized, integrated society). Then, the questionnaire was distributed to  t