Test results of eight reinforced concrete one way slab with lacing reinforcement are reported. The tests were designed to study the effect of the lacing reinforcement on the flexural behavior of one way slabs. The test parameters were the lacing steel ratio, flexural steel ratio and span to the effective depth ratio. One specimen had no lacing reinforcement and the remaining seven had various percentages of lacing and flexural steel ratios. All specimens were cast with normal density concrete of approximately 30 MPa compressive strength. The specimens were tested under two equal line loads applied statically at a thirds part (four point bending test) up to failure. Three percentage of lacing and flexural steel ratios wer

In this study the simple pullout concrete cylinder specimen reinforced by a single steel bar was analyzed for bond-slip behavior. Three-dimension nonlinear finite element model using ANSYS program was employed to study the behavior of bond between concrete and plain steel reinforcement. The ANSYS model includes eight-noded isoperimetric brick element (SOLID65) to model the concrete cylinder while the steel reinforcing bar was modeled as a truss member (LINK8). Interface element (CONTAC52) was used in this analysis to model the bond between concrete and steel bar. Material nonlinearity due to cracking and/or crushing of concrete, and yielding of the steel reinforcing bar were taken into consideration during the analysis. The accuracy of t

KE Sharquie, AA Noaimi, AG Al-Ghazzi, 2010 - Cited by 2

Background: The treatment of dental tissues proceeding to adhesive procedures is a crucial step in the bonding protocol and decides the clinical success ofrestorations. This study was conducted in vitro, with the aim of evaluating thenanoleakage on the interface between the adhesive system and the dentine treated by five surface modalities using scanning electron microscopy and energydispersiveX-ray spectrometry. Materials and methods: Twenty five extracted premolars teeth were selected in the study. Standardized class V cavities were prepared on the buccal and lingual surfaces then the teeth divided into five main groups of (5 teeth in each group n=10) according to the type of dentine surface treatment that was used: Group (A): dentine was

Breast cancer is the most common cause of death among women worldwide (1)
. Breast self-exam (BSE) is considered
an important public health procedure; primary prevention should be given the highest priority in the fight against
cancer.
Cancer is considered the second leading cause of death in developed countries there was some 6.2 million cancer
related deaths, accounƟng for 12% of all deaths globally (5).Patients perception toward this disease and preference
concerning the types and aims of their treatment are vary they may loss hopes and become devastated and crippled
or even dies earlier, if told about the diagnosis (13). The study aimed to assess knowledge of female students regarding
BSE, and to find out rel

This study focused on benthic algae (epipelic and attached algae on concrete lining stream) in Bani-Hassan stream in Holly Karbala, Iraq. The qualitative and quantitative studies of benthic algae were done by collecting 240 samples from five sites in the study area for the period from December 2012 to November 2013. Also, the environmental variables of the stream were examined in term of temporary and spatial. The results showed that the stream was alkaline, hard, oligohaline and a well aerated. The total nitrogen to the total phosphorus (TN: TP) ratio indicates nitrogen limitation. 129 species of benthic algae belonging to 57 genera were identified. Bacillariophyceae (diatoms) was the predominant taxon (95 species) followed by Chlorophyce

The Jeribe Formation, the Jambour oil field, is the major carbonate reservoir from the tertiary reservoirs of the Jambour field in northern Iraq, including faults. Engineers have difficulty organizing carbonate reserves since they are commonly tight and heterogeneous. This research presents a geological model of the Jeribe reservoir based on its facies and reservoir characterization data (Permeability, Porosity, Water Saturation, and Net to Gross). This research studied four wells. The geological model was constructed with the Petrel 2020.3 software. The structural maps were developed using a structural contour map of the top of the Jeribe Formation. A pillar grid model with horizons and layering was designed for each zone. Followin

This paper reports an experimental study of welding of dissimilar materials between transparent Polymethylmethacrylate (PMMA) and stainless steel 304 sheets using a pulsed mode Nd:YAG laser. The process was carried out for two cases; laser transmission joining (LTJ) and conduction joining (CJ). The former is achieved when the joint is irradiated from the polymer side and the latter when the joint is irradiated from the opposite side (metal side). The light and process parameters represented by the peak power (Pp), pulse duration (τ), pulse repetition rate (PRR), scanning speed (ν) and pulse shape have a significant effect on the joint strength (Fb), joint bead width (b), joint quality and appearance. The optimum parameters were determined