Devastated by the combined impact of massive drainage works and upstream damming since the 1980's, Al-Hammar Marsh, Southern Iraq, has completely collapsed with 94 % of its land cover transformed into bare land and salt crusts by 2000. After a policy initiated to restore the Iraqi marshes again in 2003, the marsh recovered about half of its former area. As a part of the ecological recovery assessment of this newly inundated marsh, it is important to investigate the extend impact of desiccation after 3 years of inundation on water quality as the latter plays an important role in the restoration process of the marshes. Therefore, from a restoration point of view, major and trace element distribution and sourcing as well as seasonal variations were studied in the re-flooded marsh of Al-Hammar. First, the Canadian Council of Ministers of the Environment Water Quality Index [1] analyses applied revealed threatened or impaired water quality and conditions in the marsh that depart from natural or desirable levels. Second, multivariate statistical techniques such as Agglomerative Hierarchal Cluster Analyses (AHCA) that were used to analyze the data and identify the possible sources of water pollution in the marsh indicated that some elements such as Ca, SO4, Mg, TDS, Cl, Na, Co, and Ni are associated with natural sourcing while other elements such as Cd, Zn, Pb, and turbidity indicated a possible anthropogenic sourcing. Third, seasonal variations investigation displayed that the water quality is affected by natural seasonal processes such as evaporation and rainfall as well as biological activities. Dry season exhibited an increase in TDS, Ca, Mg, Na, Cl, SO4, and Cd due to the concentration by evaporation during the season compared to the dilution by rainfall during the wet season. In contrast, BOD and DO levels showed a considerable decrease in dry season owing to the poor water ability to hold oxygen at high temperature as a result of higher rate of microbial metabolism.
<p>The current work investigated the combustion efficiency of biodiesel engines under diverse ratios of compression (15.5, 16.5, 17.5, and 18.5) and different biodiesel fuels produced from apricot oil, papaya oil, sunflower oil, and tomato seed oil. The combustion process of the biodiesel fuel inside the engine was simulated utilizing ANSYS Fluent v16 (CFD). On AV1 diesel engines (Kirloskar), numerical simulations were conducted at 1500 rpm. The outcomes of the simulation demonstrated that increasing the compression ratio (CR) led to increased peak temperature and pressures in the combustion chamber, as well as elevated levels of CO<sub>2</sub> and NO mass fractions and decreased CO emission values un
... Show More
The capacity factor is the main factor in assessing the efficiency of wind Turbine. This paper presents a procedure to find the optimal wind turbine for five different locations in Iraq based on finding the highest capacity factor of wind turbine for different locations. The wind data for twelve successive years (2009-2020) of five locations in Iraq are collected and analyzed. The longitudes and latitudes of the candidate sites are (44.3661o E, 33.3152o N), (47.7738o E, 30.5258o N), (45.8160o E, 32.5165o N), (44.33265o E, 32.0107o N) and (46.25691o E, 31.0510o N) for Baghdad, Basrah, Al-Kut, Al-Najaf, and Al-Nasiriyah respectively. The average wind velocity, standard deviation, Weibull shape and scale factors, and probability density functi
... Show More
(1)
Owing to the energy crisis and pollution problems of today, investigations have concentrated on
decreasing fuel consumption and on lowering the concentration of toxic components in combustion
products by using non-petroleum, renewable, sustainable and non-polluting fuels. While conventional energy sources such as natural gas, oil and coal are non-renewable, alcohol can be coupled to renewable and sustainable energy sources.
In this study, the combustion characteristics of diesel fuel and methanol blends were compared.
The tests were performed at steady state conditions in a four-cylinder DI diesel engine at full load at
1500-rpm engine speed. The experimental results showed that diesel methanol blends provided
12.7% inc
(44)
(38)
(23)
(13)
Engineering project assessment at Al-Muthana Airport in Baghdad, Iraq, has been studied using a 3D electrical resistivity imaging survey. The site investigation is crucial for assessing the future of the region's infrastructures since it reveals the location of buried facilities or weak zones below the surface and measures localized groundwater levels. Wenner-Schlumberger array was used to conduct four parallel 2D electrical resistivity spreads (MU1 to MU4). Each spread line was 100 m in length with 1 m electrode spacing and an average spacing of 9 meters between any two adjacent lines. The depth of the investigation was around 23.8 m. Survey lines were drawn going from northwest to southeast. These spreads were combined to prov
... Show More
The study area is located at AL Jabal AL-Akhdar region North Eastern part of Libya. The study includes (23) fresh samples that are taken from Darnah limestone Formation, these samples were distributed on and covered about (210) km2. The porosities and permeabilities of these samples were determined. This study is important because this formation is considered as a good reservoir for hydrocarbon accumulation in other places in Libya.
The porosity was measured by three different methods namely by porosimeter (using core samples), thin sections and binocular microscope. The permeability are also measured by two methods, the first method was by Nitrogen method and the other is by Klinkenberg method. The instrument that used for measuring
Tau-P linear noise attenuation filter (TPLNA) was applied on the 3D seismic data of Al-Samawah area south west of Iraq with the aim of attenuating linear noise. TPLNA transforms the data from time domain to tau-p domain in order to increase signal to noise ratio. Applying TPLNA produced very good results considering the 3D data that usually have a large amount of linear noise from different sources and in different azimuths and directions. This processing is very important in later interpretation due to the fact that the signal was covered by different kinds of noise in which the linear noise take a large part.
(1)
In this investigation, metal matrix composites (MMCs) were manufactured by using powder technology. Aluminum 6061 is reinforced with two different ceramics particles (SiC and B4C) with different volume fractions as (3, 6, 9 and 12 wt. %). The most important applications of particulate reinforcement of aluminum matrix are: Pistons, Connecting rods etc. The specimens were prepared by using aluminum powder with 150 µm in particle size and SiC, B4C powder with 200 µm in particle size. The chosen powders were mixed by using planetary mixing setup at 250 rpm for 4hr.with zinc stearate as an activator material in steel ball milling. After mixing process the powders were compacted by hydraulic
... Show MoreThis field experiment was conducted at Research Station B, Department of Horticulture and Landscape Engineering, College of Agricultural Engineering Sciences, University of Baghdad, Jadiriyah during the fall season of 2019-2020 to evaluate the effect of cultivation dates and soil fertilization source on the growth, yield and quality of broccoli. A split plot design within the RCBD design with three replicates was applied as the Max F1 hybrid broccoli seedlings were transferred to the field at two dates 25, Sep. 2019 and 15, Oct. 2019, which were symbolized as A and B, respectively, and occupied at the main plot. After two weeks of cultivation, the soil fertilizers were applied three times during the season in 20 days between each applicati
... Show More
(5)