The discharged water from tannery plants is main source for pollution of soil and groundwater, especially in Nahrawan area. Water samples is collected from 10 sites of wells, discharged water and from using water in different levels of tannery and 7 soil samples from different sites inside factories area and outside it. The results shown that pH for samples of wells and discharged water were within allowable limits between 6.5- 8.5, except the value of pH recorded in the discharged water sample (after the addition of calcium hydroxide) was 12.8, as well as reached the highest value of total dissolved salts (TDS) 7800 ppm in same samples. It also reached its highest value of electrical conductivity (EC) 8200 μS/cm. The results showed that most samples of discharged water recorded high values of turbidity reached to 557 NTU, while the lowest values recorded in water wells and water sample of Nahrawan village. The samples of discharged water was contained high concentration of relatively heavy elements (Pb and Ni), while not sensing concentration of (Cd and Cr), especially for non-use of chromium in the tanning process because of the lack of economic viability by the owners of the factories. The results of analysis of heavy elements in the soil samples to the concentration of Pb in the samples were all within the limits of Iraqi standard was 50-300 ppm. The results indicated that the highest concentration of Ni recorded in samples of soil in the east and south-eastern tanneries exceeding the Iraqi standard concentration of Ni in the soil the amount of 30-75 ppm, while the concentration of Ni in other soil samples was within the limits of the Iraqi standard, while not sensing by concentration of (Cd and Cr) in these samples.
Rates of zinc consumption during cathodic protection of a copper pipeline carrying saline water were measured by the loss in weight technique. The study of sacrificial anode cathodic protection of short copper tube using zinc strip extended axially in the pipe revealed that : (i) The increase of zinc consumption with time of exposure (1-3 h's) at different flow rates (turbulent flow) (300-600 l/hr) while the temperature , solution concentration and the pH were fixed at 20ºC, 3.5%wt NaCl, and pH=8 respectively in absence and presence of bacteria.(ii)Increase of zinc consumption with flow rates (300-600 l/hr) at different temperatures (10-40ºC) while solution concentration and time of exposure were fixed at 3.5 %wt NaCl and 3hr's respect
... Show MoreDue to the broad range uses of chromium for industrial purposes, besides its carcinogenic effect, an efficient, cost effective removal method should be obtained. In this study, cow bones as a cheap raw material were utilized to produce active carbon (CBAC) by physiochemical activation, which was characterized using: SEM to investigate surface morphology and BET to estimate the specific surface area. The best surface area of CBAC was 595.9 m2/gm which was prepared at 600 ᵒC activation temperature and impregnation ratio of 1:1.5. CBAC was used in aqueous chromium ions adsorption. The investigated factors and their ranges are: initial concentration (10-50 mg/L), adsorption time (30-300 min), temperature (20-50
... Show More
(8)
Twelve species of Tubuliferous thrips, of the family Phlaeothripidae had been reported from Iraq. Two of these were reported previously, Haplothrips cerealis Priesner, by El-Haidari and Daoud 1971 and Haplothrips tritici kurdjumov by Al-Ali 1977 and the rest were recorded for the first time: these are Haplothrips hukkineni Priesner; Haplothrips subtilissimus (Haliday); Haplothrips reuteri Karny; Haplothrips jasonis Priesner; Haplothrips sallloumensis Priesner; Haplothrips pharao Priesner; Phlaeothrips sycomri Priesner; Karnyothrips flavipus (Jones); Karnyothrips melaleucus (Bagnall); Dolicholepta micrurus (Bagnall). Number of insec
... Show More
(1)
(3)
This Investigation aims to study the effect of adding Steel fibers with different volume fractions Vf (o.5, 0.75, and 1% by volume of concrete) with aspect ratio 100 on mechanical properties of concrete, and also
finding the influence of petroleum products (Kerosene and Diesel) on mechanical properties of Steel Fiber Reinforced Concrete (SFRC).
The experimental work consists of two groups: group one consists of specimens (cubes and prisms) plain and concrete reinforced with steel fiber exposed to continuous curing with water. Group two consists of
specimens (cubes and prisms) plain and concrete reinforced with steel fiber exposed to kerosene and diesel after curing them in water for 28 days before exposure. The results of all te
(9)