Seismic inversion technique is applied to 3D seismic data to predict porosity property for carbonate Yamama Formation (Early Cretaceous) in an area located in southern Iraq. A workflow is designed to guide the manual procedure of inversion process. The inversion use a Model Based Inversion technique to convert 3D seismic data into 3D acoustic impedance depending on low frequency model and well data is the first step in the inversion with statistical control for each inversion stage. Then, training the 3D acoustic impedance volume, seismic data and porosity wells data with multi attribute transforms to find the best statistical attribute that is suitable to invert the point direct measurement of porosity from well to 3D porosity distribut

The calculation of the oil density is more complex due to a wide range of pressuresand temperatures, which are always determined by specific conditions, pressure andtemperature. Therefore, the calculations that depend on oil components are moreaccurate and easier in finding such kind of requirements. The analyses of twenty liveoil samples are utilized. The three parameters Peng Robinson equation of state istuned to get match between measured and calculated oil viscosity. The Lohrenz-Bray-Clark (LBC) viscosity calculation technique is adopted to calculate the viscosity of oilfrom the given composition, pressure and temperature for 20 samples. The tunedequation of state is used to generate oil viscosity values for a range of temperatu

3D seismic reflection structural study of (250) km² of Balad Oil field located in central part of Iraq within Salah Al-din province (Balad area) was carried out.
Faults were picked using instantaneous phase attribute of seismic sections and variance attribute of seismic time slices across 3D seismic volume.
A Listric growth normal fault is affecting the succession of Cretaceous Formation and cut by strike slip fault. In addition, minor normal faults (Dendritic and tension faults) are developed on the listric normal growth fault. As a result, a major graben is separated by Strike slip fault into two parts (north and south parts) and trend in NW-SE direction.

The gravity field of southern Iraq shows steep gradient of regional trend. The gravity contours over the anticline structures in this area do not show the closure characteristic of these structures. The effect of lateral density variation for Hormuz Salt complicates the case in the area. Higher derivatives are one of the means that have been used to remove the effect of such regional gravity variations, which can easily mask significant structures. Biharmonic Operator is used to delineate these distort structures, follow their extent and at the same time distinguish new features. The Biharmonic operator manipulation has ability to suppress the effect of regional and enhance the local anomalies. The problem with higher derivatives operati

The detailed data of the Vp/Vs ratio and porosity logs were used to detect the Oil-Water Contact Zone (OWCZ) of Nahr Umr sandstone and Mishrif limestone reservoir formations in Kumiat (Kt) and Dujaila (Du) oil fields, southeastern Iraq. The results of OWC were confirmed using P-wave, Resistivity, and Water Saturation (Sw) logs of Kt-1 and Du-1 wells. It was found that the values of the oil-water contact zone thickness in Nahr Umr sandstone and Mishrif limestone were approximately one meter and eight meters, respectively. These results suggest that the OWCZ is possibly thicker in the carbonate rock than clastic rock formations. The thickness of OWCZ in the clastic rocks changed from one part to another, depending on several factors includ

Twenty nine core samples were taken from Ratawi 7 Oil well according to the presence of oil in formation and availability of core samples. This well is located in the province of Basra/southern Iraq. The samples were collected from Yamama Formation. The core samples are taken from the well at different depths, ranging between (3663m-3676m). The range of Vp for these core samples is (668-4017 m/sec) and its average is (1779 m/sec), While the range of Vs is (291-1854 m/sec) and its average is (796 m/sec). In the current study the ultrasonic method is conducted to measure Vp, Vs as well as some petrophysical properties for core samples and some elastic moduli such as (Young's modulus, Bulk modulus, Shear modulus, Poisson's ratio and Lame's

Knowing the distribution of the mechanical rock properties and in-situ stresses for the field of interest is essential for many applications concerning reservoir geomechanics, including wellbore instability analysis, hydraulic fracturing, sand production, reservoir compaction, subsidence and water/gas injection throughout the filed life cycle. Determining the rock's mechanical properties is challenging because they cannot be directly measured at the borehole. The recovered carbonate core samples are limited and only provide discrete data for specific depths. This study focuses on creating a detailed 1D geomechanical model of the Mishrif reservoir in the Nasriyah oil field to identify the fault regime type for each unit in the format

Oil seep samples along Abu-Jir Fault Zone were studied to determine their chemical characterization and origin. They are dominated by the normal alkanes, more complex mixture of branched and cyclic hydrocarbons. Organofacies coupled with the stable carbon isotopes have been integrated to infer the oil seep origin. Oil seeps contain H2S gas, which derives as a catabolic by product of sulfate-reducing bacteria from gypsum of the Fatha Formation during the early diagenetic under anoxic conditions which is demonstrated by values of C29/H that are greater than 1. The oil seeps are characterized by δ13C values vary from -29.0 to -27.96‰ and from -28.34 to -27.88‰ in the saturated and aromatic compounds, respectively; consequently, they ha

   Petrophysical characterization is the most important stage in reservoir management. The main purpose of this study is to evaluate reservoir properties and lithological identification of Nahr Umar Formation in Nasiriya oil field. The available well logs are (sonic, density, neutron, gamma-ray, SP, and resistivity logs). The petrophysical parameters such as the volume of clay, porosity, permeability, water saturation, were computed and interpreted using IP4.4 software. The lithology prediction of Nahr Umar formation was carried out by sonic -density cross plot technique. Nahr Umar Formation was divided into five units based on well logs interpretation and petrophysical Analysis: Nu-1 to Nu-5. The formation lithology is mainly