This research involves the study of permeability declination as a result of kaolinite due to the changing in pH in the Zubair reservoir (Lower Cretaceous) during the secondary production by water injection method. Four wells and six core samples within the North Rumaila field are studied, Minerals have been diagnosed by XRD and this specific site of clay minerals was diagnosed within the core samples by scanning electron microscopy (SEM). The core samples are also studied petrogrphically using the polarizing microscope and found that they mainly consist of quartz, while the predominant clay is kaolinite. The effect of pH on the values of permeability was examined through a series of laboratory experiments, as it has been tested in the cases of gradual sudden increase form acidic to alkaline. Petrophysical properties (porosity and initial permeability) were measured a prior to testing. After performing these tests, the final permeability was also measured as well as the rate of formation damage. The final permeability decreased gradually at a rate of 20-30% M Darcy during the injection out with solution of pH 3 to 11 with getting formation damage up to 25%. While in the case injection with sudden increase pH from acid to alkaline directly, there has been a rapid and substantial reduction in the final permeability as average of 28% -72%, with a formation damaged rate of 44%. The results confirmed that the reason of the decrease in the permeability is due to the kaolinite mineral which is subject to the dispersion phenomenon during the change in pH, and the acidic environment is suitable for the reservoir, and does not lead to a reduction in permeability.
Functionalized-multi wall carbon nanotubes (F-MWCNTs) and functionalized-single wall carbon nanotubes (F-SWCNTs) were well enhanced using CoO Nanoparticles. The sensor device consisted of a film of sensitive material (F-MWCNTs/CoONPs) and (F-SWCNTs/CoO NPs) deposited by drop- casting on an n-type porous silicon substrate. The two sensors perform high sensitivity to NO2 gas at room temperatures. The analysis indicated that the (F-MWCNTs/CoONPs) have a better performance than (F-SWCNTs/CoONPs). The F-SWCNTs/CoONPs gas sensor shows high sensitivity (19.1 %) at RT with response time 17 sec, while F-MWCNTs/CoONPs gas sensor show better sensitivity (39 %) at RT with response time 13 sec. The device shows a very reproducible sensor p
... Show More
(5)
Aggregate production planning (APP) is one of the most significant and complicated problems in production planning and aim to set overall production levels for each product category to meet fluctuating or uncertain demand in future. and to set decision concerning hiring, firing, overtime, subcontract, carrying inventory level. In this paper, we present a simulated annealing (SA) for multi-objective linear programming to solve APP. SA is considered to be a good tool for imprecise optimization problems. The proposed model minimizes total production and workforce costs. In this study, the proposed SA is compared with particle swarm optimization (PSO). The results show that the proposed SA is effective in reducing total production costs and req
... Show More
(10)
(3)
In this investigative endeavor, a novel concrete variety incorporating sulfur-2,4-dinitrophenylhydrazine modification was developed, and its diverse attributes were explored. This innovative concrete was produced using sulfur-2,4-dinitrophenylhydrazine modification and an array of components. The newly created sulfur-2,4-dinitrophenylhydrazine modifier was synthesized. The surface texture resulting from this modifier was examined using SEM and EDS techniques. The component ratios within concrete, chemical and physical traits derived from the sulfur-2,4-dinitrophenylhydrazine modifier, chemical and corrosion resistance of concrete, concrete stability against water absorption, concrete resilience against freezing, physical and mechanical p
... Show More
(4)
To evaluate and improve the efficiency of photovoltaic solar modules connected with linear pipes for water supply, a three-dimensional numerical simulation is created and simulated via commercial software (Ansys-Fluent). The optimization utilizes the principles of the 1st and 2nd laws of thermodynamics by employing the Response Surface Method (RSM). Various design parameters, including the coolant inlet velocity, tube diameter, panel dimensions, and solar radiation intensity, are systematically varied to investigate their impacts on energetic and exergitic efficiencies and destroyed exergy. The relationship between the design parameters and the system responses is validated through the development of a predictive model. Both single and mult
... Show More
(8)
(7)
(10)
(9)
This paper reports an experimental study of welding of dissimilar materials between transparent Polymethylmethacrylate (PMMA) and stainless steel 304 sheets using a pulsed mode Nd:YAG laser. The process was carried out for two cases; laser transmission joining (LTJ) and conduction joining (CJ). The former is achieved when the joint is irradiated from the polymer side and the latter when the joint is irradiated from the opposite side (metal side). The light and process parameters represented by the peak power (Pp), pulse duration (τ), pulse repetition rate (PRR), scanning speed (ν) and pulse shape have a significant effect on the joint strength (Fb), joint bead width (b), joint quality and appearance. The optimum parameters were determined
... Show More
(73)
(61)
(12)
(7)
(6)
(5)
Roughness length is one of the key variables in micrometeorological studies and environmental studies in regards to describing development of cities and urban environments. By utilizing the three dimensions ultrasonic anemometer installed at Mustansiriyah university, we determined the rate of the height of the rough elements (trees, buildings and bridges) to the surrounding area of the university for a radius of 1 km. After this, we calculated the zero-plane displacement length of eight sections and calculated the length of surface roughness. The results proved that the ranges of the variables above are ZH (9.2-13.8) m, Zd (4.3-8.1) m and Zo (0.24-0.48) m.
(6)
(2)
Inflammatory bowel disease includes both Crohn’s disease and ulcerative colitis, is a chronic, progressive relapsing disease of gastrointestinal tract that require long-term treatment or maintenance therapy. Taking patient’s beliefs about the prescribed medication in consideration had been shown to be an important factor that affects compliance of the patient in whom having positive beliefs is a prerequisite for better compliance. The aim of the current study was to investigate and assess beliefs about medicines among a sample of Iraqi patients with inflammatory bowel disease and to determine possible association between these beliefs and some patient-specific factors.
This study is a cross-sectional study carried out o
... Show More
(3)
(2)