Agricultural lands have great importance in people's lives, and their exploitation has a great impact on strengthening the national economy. Therefore, countries have given great importance to this sector, and because of the importance of this sector, the state has given large areas of these lands to the farmers to invest in agriculture, and among these farmers are those who died and left behind children who took up crafts. Agriculture, for fear that these agricultural lands would be abandoned and turned into waste lands, a land system was introduced called (regular distribu- tion), which corresponds to (legitimate inheritance). Under this system, these lands were trans- ferred to the children of farmers who died so that the process of inve

The research deals with the problem of visual pollution, as it is one of the most important urban problems that cities suffer from. The concept of visual pollution has recently emerged to describe the deformation and degradation of the urban environment. Visual pollution is defined as any component of the surrounding environment that is inconsistent and not homogeneous with its natural and human components. The volume of visual pollution has doubled due to the non-compliance with the laws, regulations and controls set by the Municipality of Baghdad by the citizens, and to the weak municipal role that the municipality plays in implementing these laws. Therefore, it has become necessary to know the manifestations of visual pollution and th

  This research studies the effect of grain size for the final stage in sintering Al2O3 .The experimental results for α- Al2O3 powder are modeled using ( L2-Regression ) technique in  order to study the effect grain size distribution on densification rate using four kinds for the initial particle size which were ( 1.44 , 2.54 , 0.7-2.54 ,1.15-3.53 ) µm , and for sintering time  (0-241) min. The mathematical simulation for grain size changing shows that the densification rates boots up as the grain size goes lower, this was due to the increase of contact area between the grains.

This paper has investigated experimentally the dynamic buckling behavior of AISI 303 stainless steel Aluminized and as received long columns. These columns, hot-dip aluminized and as received, are tested under dynamic buckling, 22 specimens, without aluminizing (type 1), and 50 specimens, with hot-dip aluminizing at different aluminizing conditions of dipping temperature and dipping time (type 2), are tested under dynamic compression loading and under dynamic combined loading (compression and bending) by using a rotating buckling test machine. The experimental results are compared with Perry Robertson interaction formula that used for long columns. Greenhill formula is used to get a mathematical model that descripts the buckling behavior

The process of granting loans by banks is the confidence they give to their customers, but this trust should not be a cornerstone in granting loans even if granted these loans on the basis of sound banking should involve risks that may be exposed to the bank because of the failure of the client to meet The bank's financial obligations to the bank due to the unexpected economic conditions affecting the customers, which makes them in a state of faltering, which weaken the ability of banks to provide loans, which are the most important sources of revenue and profits, so the problem of non-performing loans is one of the main problems facing most of the banks Which impede the functioning of its work and the reasons that led to the agg

The current research aims to provide a philosophical and knowledge framework  to explain the issue of organizations dealing with Paradox phenomena by focusing on five main aspects. The first deals with the concept of paradox, and the second aspect deals with the types of forces paradox. While the third aspect regards subject of the philosophy of paradox in organization theory and the fourth side deals with methods of   solving the paradox. Finally, the last side is exposed to the subject of the paradoxes of the three provided by the study (L

Twelve students rinsed their mouths once daily with ten ml. of 0.2 % aqueous solution of chlorhexidine gluconate for five days, and seven students served as a control group that used distilled water for rinsing. The result indicated that after one hour of treatment, an obvious sharp reduction in the viable counts of mutans streptococci, total aerobic bacteria, and to less extent the count of lactobacilli in saliva after one hr. of treatment. AnØ¢  increase in the number of these bacterial groups was clearly noticed three hrs. after the application of chlorhexidine and continued to increase later on. In spite of that increase, the bacterial numbers in saliva remained below the initial numbering in this study.

Experimental results for the density of states of hydrogenated amorphous silicon due to Jackson et al near the valence and conduction band edges were analyzed using Levenberg-Marquardt nonlinear fitting method. It is found that the density of states of the valence band and the conduction band can be fitted to a simple power law, with a power index 0.60 near the valence band edge, and 0.55 near the conduction band edge. These results indicate a modest but noticeable deviation from the square root law (power index=0.5) which is found in crystalline semiconductors. Analysis of Jackson et al density of states integral J(E) data over about (1.4 eV) of photon energy range, showed a significant fit to a simple power law with a power index of 2.11

The transition structure is considered as the most important hydraulic structure controlling the w/s transtion, morever it decrease the scouring of outlet structure.

seven experiment samples for transition structure was used in this research at different angles ( 10° - 90° ).

       It was shown that froud number has a clear effect on the depth of the scouring, morever the high discharge rates cause an increase of the ratio between the length of the scour and its depth.

       In order to select the best flaring angle it was shown that the angle of 40° has the most discharge rate, least structure length and least angle scour depth, with the firmly of t