This research investigated the effectiveness of using different thickness values of polyimide (PI) interfacial layer in order to improve electrical and thermal properties of Al/ PI /c-Si capacitor. The PI spectra produced by poly(amic acid) (PAA) were characterized by using FT-IR analysis. After imidization of PAA, some absorption peaks vanished, whereas PI peaks appeared, due to the complete conversion of PAA to PI.

    The results show that thermal decomposition resistance of polyimide films increases with the increase of polyimide thickness, because of the increase of the imide bond and the decrease of the average distance between amide groups.

The study intends to well logs interpretation to determine the petrophysical parameters of Euphrates Formations in Ajeel Oil Field. The petrophysical properties have been determined from well logging, Euphrates Formation in terms of reservoirs units, consist of two Petrophysical properties. Total porosity, effect porosity and secondary porosity have been calculated from neutron, density, and sonic logs. secondary porosity is high and it's resulted from diagenesis processes in the formation. From RHOB-NPHI and N/M cross plot, Euphrates Formation composed mainly from Limestone and dolomite with nodules of anhydrite. Dhiban Formation composed mainly of anhydrite, so it's represented the cap rocks for Euphrates Reservoir were recognized base

Mishrif Formation regards one of the most important reservoirs in Iraq. Well logging represents one of the most important tool in the formation evaluation. According to the Petrophysical properties that have been gotten from well logging, Mishrif Formation in terms of reservoirs units, consist of several reservoirs units. Major reservoirs units divided into three reservoir units,MA,MB&MC. Each of these major units divided into minor reservoirs units (MB11,MB12,MC2&MC3).MB major reservoir units represent the best reservoir unit. These reservoirs units separated by cap rocks(mainly tight limestone)(CR1,CR2,CR3,CR4,CR5,CR6,and CR7).CPI were demonstrated for all wells.Hydrocarbon saturation vs.

        In this paper, mixed spinel Co_0.4Zn_0.6Fe₂O₄ ferrite was synthesized by microwave-assisted combustion method. Photocatalytic activity of the as-synthesized sample was investigated against methylene blue dye at room temperature at different exposure times (60-360 min.) under visible light. Phase impurity and surface morphology which are investigated with XRD analysis and field emission- scanning electron microscopy, indicate that a cubic spinel unit cell structure with a crystilite size and lattice constant are 22.5048nm and 8.37Å, respectively. The saturation magnetization exhibited directly from the hysteresis loop is (70.20emu/g). Optical properties for the investigated ferrite

Light has already becomes a popular means of communication, and the high-bandwidth data into free space without the use of wires. A great idea took us to design a new system for transmitting sound through free space at (650, 532) nm wavelengths using reflective mirrors under different atmospheric conditions. The study showed us the effect of various weather factors (temperature, wind speed and humidity) on these wavelengths for different distances. As well as studying the attenuation caused by long-distance laser and beam divergence, A reflective dish was used to focus the spot of the laser beam on the photocell. Results were discussed under the effect of these factors and the attenuation resulting from the beam divergence. Thus, the sys

      This study shows the effects of copper material electrode, applied voltage, and different pressure values on electrical discharge plasma. The purpose of the work is the application of the spectral analysis method to obtain accurate results of nitrogen plasma parameters. By using the optical emission spectroscopy (OES), many N₂ molecular spectra peaks appeared in the range from 300 to 480 nm. Also, some additional peaks were recorded, corresponding to atomic and ionic lines for nitrogen, target material, and hydrogen, in all samples. The electron density (n_e) was calculated from the measurement of Stark broadening effect, which was found to decrease with increasing pressure from 0.1 mba

In this study, nanocomposites have been prepared by adding
multiwall carbon nanotubes (MWCNTs) with weight ratios (0, 2, 3,
4, 5) wt% to epoxy resin. The samples were prepared by hand lay-up
method. Influence of an applied load before and after immersion in
sodium hydroxide (NaOH) of normality (0.3N) for (15 days) at
laboratory temperature on wear rate of Ep/MWCNTs
nanocomposites was studied. The results showed that wear rate
increases with increasing the applied load for the as prepared and
immersed samples and after immersion. It was also found that epoxy
resin reinforced with MWCNTs has wear rate less than neat epoxy.
The sample (Ep + 5wt% of MWCNTs) has lower wear rate. The
immersion effect in base so

The purpose of this study was to determine the effect of lupine flour (L.f) and lupine protein concentrate (L.P.C) incorporation on chemical, nutritional and sensual qualities characteristics of biscuit (L.P.C) was prepared by isoelectric precipitation method. A standard recipe for biscuit preparation by wheat patent flour used as the control. Wheat flour in the control treatment was replaced with (L.f) and (L.P.C) at levels 10, 20 & 30%. Chemical composition of (L.f), (L.P.C) and biscuit treatments were studied. Results showed that protein contents were 35.35 & 75.80% for (L.F) and (L.P.C), respectively. While they amounted to 14.70, 16.16 & 18.61% for (L.f) incorporated biscuits and

The synthesis and characterisation of new macrocyclic binuclear metal(II) complexes derived from dithiocarbamate (DTC) ligand are reported. The reaction of a bis-secondary amine, CS2 and KOH resulted in the formation of the free ligand. Two approaches were implemented to synthesis the macrocyclic bis(dithiocarbamate) complexes; (i) from the reaction of the free ligand with a metal ion, and (ii) via a one-pot reaction. In the free ligand approach, complexes were obtained by the reaction of dithiocarbamate salt with the metal ions; CoII, ZnII and CdII. However, the one-pot reaction is based on the mixing of the bissecondary amine, CS2, KOH and metal(II) chloride. Physico-chemical analyses were implemented to characterise the ligand and its