The current study summarized the construction of a three-dimensional geological model of the Aquitanian sediments age, which represented by the Euphrates and Serikagni formation in Ajeel Oil Field, where Ajeel Oil Field has structural closure towards northwest - southeast. Sedimentary of the current study consist of limestone, dolomitic limestone, dolomite (compose of skeletal grains, non-skeletal grains and cement) and the appearance of some anhydrite rocks.

     The petrographic study of the Euphrates Formation were prepared using a thin section of wells (Aj-1, Aj-4, Aj-5, Aj-6 and Aj-7), Previous studies and geological reports, as well as use well logs data  in the statistical analysis by Petrel softwa

     This study is achieved in the local area of the Eridu oil field, where the Mishrif Formation is considered the main productive reservoir. The Mishrif Formation was deposited during the Cretaceous period in the secondary sedimentary cycle (Cenomanian-Early Turonian as a part of the Wasia Group, a carbonate succession widespread throughout the Arabian Plate.

     The Mishrif Formation already have been evaluated in terms of depositional environments and their diagenetic processes. Here, it will test the previous conclusions with petrophysical properties delineated by using well logging. The results show there is a fully matching with two reservoir units (MA and MB). Dissolution and primary porosity are responsible for f

      It is common that extraterrestrial solar radiation R_a value lessen due to the interaction with atmosphere components to result a net solar radiation R_n value about one third of R_a for most measurements on earth. Net solar radiation had major impact on air temperature (T_o) value statement. So, its estimation is crucial for analyzing the interaction of (atmosphere-vegetation-soil).

Many methodologies available for this aim directly (with radiometer) or indirectly (with air temperature-based formula or soil plus air temperatures-based formula). The peak influences of global warming phenomenon were in eighties decade of the last century, yielding Iraq R_n rates to get cl

Reservoir fluids properties are very important in reservoir engineering computations such as material balance calculations, well testing analyses, reserve estimates, and numerical reservoir simulations. Isothermal oil compressibility is required in fluid flow problems, extension of fluid properties from values at the bubble point pressure to higher pressures of interest and in material balance calculations (Ramey, Spivey, and McCain). Isothermal oil compressibility is a measure of the fractional change in volume as pressure is changed at constant temperature (McCain). The most accurate method for determining the Isothermal oil compressibility is a laboratory PVT analysis; however, the evaluation of exploratory wells often require an esti

As the reservoir conditions are in continuous changing during its life, well production rateand its performance will change and it needs to re-model according to the current situationsand to keep the production rate as high as possible.Well productivity is affected by changing in reservoir pressure, water cut, tubing size andwellhead pressure. For electrical submersible pump (ESP), it will also affected by numberof stages and operating frequency.In general, the production rate increases when reservoir pressure increases and/or water cutdecreases. Also the flow rate increase when tubing size increases and/or wellhead pressuredecreases. For ESP well, production rate increases when number of stages is increasedand/or pump frequency is

In drilling processes, the rheological properties pointed to the nature of the run-off and the composition of the drilling mud. Drilling mud performance can be assessed for solving the problems of the hole cleaning, fluid management, and hydraulics controls. The rheology factors are typically termed through the following parameters: Yield Point (Yp) and Plastic Viscosity (μp). The relation of (YP/ μp) is used for measuring of levelling for flow. High YP/ μp percentages are responsible for well cuttings transportation through laminar flow. The adequate values of (YP/ μp) are between 0 to 1 for the rheological models which used in drilling. This is what appeared in most of the models that were used in this study. The pressure loss

The Fauqi field is located about 50Km North-East Amara town in Missan providence in Iraq. Fauqi field has 1,640 MMbbl STOIIP, which lies partly in Iran. Oil is produced from both Mishrif and Asmari zones. Geologically, the Fauqi anticline straddles the Iraqi/Iranian border and is most probably segmented by several faults. There are several reasons leading to drilling horizontal wells rather than vertical wells. The most important parameter is increasing oil recovery, particularly from thin or tight reservoir permeability. The Fauqi oil field is regarded as a giant field with approximately more than 1 billion barrels of proven reserves, but it has recently experienced low production rate problems in many of its existing wells. This study

Engineering equipment is essential part in the construction project and usually manufactured with long lead times, large costs and special engineering requirements. Construction manager targets that equipment to be delivered in the site need date with the right quantity, appropriate cost and required quality, and this entails an efficient supplier can satisfy these targets. Selection of engineering equipment supplier is a crucial managerial process .it requires evaluation of multiple suppliers according to multiple criteria. This process is usually performed manually and based on just limited evaluation criteria, so better alternatives may be neglected. Three stages of survey comprised number of public a

      Zubair Formation is the most productive reservoir in southern Iraq, which is comprised of sandstones, interbedded with shale sequences and sometimes carbonate rock. It is an important formation in the lower Cretaceous cycle in Iraq. Rumaila oil field is the largest oil field in Iraq and the 6th in the world. Two wells were studied for three depths, one in the southern Rumaila and the other in the north. The study focused on light and heavy minerals in sand fractions and their relationship with hydrocarbon assemblages. For the survey to be complete, the sedimentological study of the cores was also conducted. This research aims to determine the effect of the amount of heavy and light minerals on the generation and production of

Setting-up a 3D geological model both from field and subsurface data is a typical task in geological studies involving natural resource evaluation and hazard assessment. In this study a 3D geological model for Mishrif Formation in Garraf oil field has been set-up using Petrel software. Mishrif Formation represents the most important reservoir in Garraf oil field. Four vertical oil wells (GA-4, GA-A1P, GA-3 and GA-5) and one directional well (GA-B8P) were selected in Garraf Oil Field in order to set-up structural and petrophysical (porosity and water saturation) models represented by a 3D static geological model in three dimensions. Structural model shows that Garraf oil field represents a domal structure that shows continuous growth as i