Background: Denture relining is the process of resurfacing of the tissue side of the ill fitting denture, the bond strength at the relining-denture base interface is most important for denture durability.The aim of present study was to evaluate the shear bond strength between the thermosens as relining material and different denture base materials that bonded by thermo fusing liquid. As this corrective procedureis the common chair side procedure in the dental clinic. Material and method: Sixty samples were prepared and divided into three main groups according to the type of denture base materials.Group (A) referred to the heat cure acrylic samples which consisted of 20 samples. Group (B) referred to the high impact acrylic samples which con

This research is presented experimental and numerical investigations of composite concrete-steel plate shear walls under axial loads to predicate the effect of both concrete compressive strength and aspect ratio of the wall on the axial capacity, lateral displacement and axial shortening of the walls. The experimental program includes casting and testing two groups of walls with various aspect ratios. The first group with aspect ratio H/L=1.667 and the second group with aspect ratio H/L=2. Each group consists of three composite concrete -steel plate wall with three targets of cube compressive strength of values 39, 54.75 and 63.3 MPa. The tests result obtained that the increase in concrete compressive strength results in increasing

The aim of the research is to: Analyzing the content of the mathematics textbook of the 5th bio-scientific grade according to the Common Core State Standard for mathematics (CCSSM), and to identify the extent of their inclusion of these standards. To achieve this goal, the researcher built the CCSSM after reviewing the literature that dealt with those standards, and its validity was verified by presenting it to a group of referees specialized in the field of methods of teaching mathematics. Thus, the criteria in their final form consisted of six main criteria which are:(numbers and quantities, algebra, conjugations, modeling, geometry, statistics and probability) and included (47) sub-indicators, Then the researcher analyzed the content of

A reinforced concrete frame is referred as "RIGID FRAMES". However, researches indicate that the Beam-Column joint (BCJ) is definitely not rigid. In addition, extensive research shows that failure may occur at the joint instead of in the beam or the column. Joint failure is known to be a catastrophic type which is difficult to repair.
This study was carried out to investigate the effect of hoops and column axial load on the shear strength of high-strength fiber reinforced Beam-Column Joints by using a numerical model based on finite element method using computer program ANSYS (Version 11.0). The variables are: diameter of hoops and magnitude of column axial load.
The theoretical results obtained from ANSYS program are in a good a

A new tool geometry was used to achieve friction stir spot welding (FSSW) in which the shoulder was designed separately from the rotating pin, and in order to examine weldment strength through the modified tool, a lap joints of AA2024 aluminum alloy plate 1 mm thick were welded successfully by using 6 mm pin diameter and varying process parameters (rotational speeds, tool nose geometry, and depth of tool penetration in the lower welded plate). Experimental tests indicate that the maximum average tensile shear load was 3100 N at the best selected condition. Microstructure examination and micro hardness test along the spot zones were investigated as well as measuring pin penetration load. Visual inspection of the welded spot surface shows a g

Aim: The aim of this study is to determine the correlation between levels of certain seminal biochemical parameters and serum reproductive hormones, on the one hand, and sperm function tests, on the other hand, in asthenospermic patients. Patients and Methods: Sixty asthenospermic patients and twenty fertile men as a control group were included in this study. Semen samples were collected to perform seminal fluid analysis. Total protein, cholesterol, calcium, creatine kinase, and fructose were measured in the seminal plasma. Blood samples were collected for hormonal assay of serum reproductive hormones: testosterone, prolactin, luteinizing hormone, and follicle-stimulating hormone. Results: The results revealed a significant positive correla

Hypertension is one of the leading causes of the global burden of disease, which causes serious health problems. The aim of this study is to investigate the lipid profile levels in sera of Iraqi hypertensive patients by measuring Total cholesterol (TC), triglyceride (TG) and low density lipoproteins (LDL) and kidney function levels by measuring uric acid, urea and creatinine. Seventy five individuals of Iraqi adults (Males) were divided into three groups: 25 hypertensive patients with duration of disease (1-10) year (group 1), 25 hypertensive patients with duration of disease (11-30) year (group 2) and 25 normal individuals as control group (group3). The findings indicate that serum (TC, TG and LDL) levels were significantly elevated (

Ninety five samples were collected from different samples (urine, ear and wounds swaps), from hospitals in Baghdad city. The results of cultural, microscopic , biochemical tests indicated that in urine samples E.coli have high occurrence frequency 19 (47.5%) followed by Proteus mirabilis 18(45%) and Klebsiella species 1 (2.5%), while in wounds samples each of Pseudomonas spp. and Proteus mirabilis 10 (25%) , then followed by E.coli with 5 (12.5%) and Klebsiella species 3 (7.5%). Ear swaps samples revealed that Pseudomonas aeruginosa 7 (46%) was the major bacterium followed by Proteus mirabilis 4(26.6).Sensitivity test against eleven antimicrobial agents was done for all of the Proteus mirabilis isolates (32 isolates). The results display

The research aims to identify small and medium enterprises in accounting thought in terms of definition and concept, and this international financial reporting standard for small and medium-sized enterprises (SMEs) in the theoretical aspect. As for the practical aspect, the small and medium-sized enterprises standard has been applied to the financial statements of the company in question, the preparation of the opening entry on the date of the transition, the requirements of measurement and the accounting disclosure on the date following the application of the standard, and the preparation of the company's financial statements and the accompanying explanations according to the standard of small and medium-sized enterprises. The r