The aim of the research is to measure the efficiency of the companies in the industrial sector listed in the Iraqi Stock Exchange , by directing these companies to their resources (inputs) towards achieving the greatest possible returns (outputs) or reduce those resources while maintaining the level of returns to achieve the efficiency of these companies, therefore, in order to achieve the objectives of the research, it was used (Demerjian.et.al) model to measure the efficiency of companies and the factors influencing them. The researchers had got a number of conclusions , in which the most important of them is that 66.6% of the companies in the research sample do not possess relatively high efficiency and that the combined factors (the nat

   The aim of the research is to measure the efficiency of the companies in the industrial sector listed in the Iraqi Stock Exchange , by directing these companies to their resources (inputs) towards achieving the greatest possible returns (outputs) or reduce those resources while maintaining the level of returns to achieve the efficiency of these companies, therefore, in order to achieve the objectives of the research, it was used (Demerjian.et.al) model to measure the efficiency of companies and the factors influencing them. The researchers had got a number of conclusions , in which the most important of them is that 66.6% of the companies in the research sample do no

The current study has beenconduced to evaluate the effect of extracted crude terpens at the concentrations of 6,8% of seeds of Eucalyptuscamaldulensison the 4th larval instar oftheCallosobruchusmaculates and the percentage of the cowpea seed germination.The Results showed that the terpens extract of the concentration of 8% increases the mortality rate of the fourth larval instar and it reach to 63.3%, and then decrease of to 26.6,20% at concentration of 6%and forcontrol treatment respectively The percentage of adult emergence reduces to 0% at the concentration of 8% compared with control treatment in which it reach to 66.6%. The extraction atbothconcentrations 6,8% does not affect the germination rate

Knowledge of the mineralogical composition of a petroleum reservoir's formation is crucial for the petrophysical evaluation of the reservoir. The Mishrif formation, which is prevalent in the Middle East, is renowned for its mineralogical complexity. Multi-mineral inversion, which combines multiple logs and inversions for multiple minerals at once, can make it easier to figure out what minerals are in the Mishrif Formation. This method could help identify minerals better and give more information about the minerals that make up the formation. In this study, an error model is used to find a link between the measurements of the tools and the petrophysical parameters. An error minimization procedure is subsequently applied to determine

Dentures that are not cleaning and maintained properly may prone to contamination by different microbial pathogens that result in several oral conditions. This study was design to compare the antimicrobial effect of different denture cleansers oxalic, tartaric, citric acids and alkaline peroxide with microwave irradiation on the growth of Candida albicans and Staphylococcus aureus respectively. Microwave oven used to disinfect specimens of heat-activated acrylic resin and soft linear. Oxalic, citric, tartaric acids, and alkaline peroxide were also used. Microorganisms that tested were Candida albicans and Staphylococcus aureus separately. Treatment with microwave or tartaric acid could achieve sterilization of both hot cured acrylic resins

Abstract

Electrical magnate  was designed and constructed,  the optimum Magnetic flux  and the effect of time on the physical properties of the alkaline (magnetic water) produced from the bottled drinking water [the total dissolved solids (TDS) or the electrical conductivity, and pH] were studied, to simulate ZamZam water in Mekka Saudi Arabia. Also, the efficiency of magnetic field from this designed electrical magnate in decreasing the TDS of sea water (of 1500 ppm NaCl Content), to convert it to water suitable for irrigation (TDS<1000 ppm) was investigated in this work.The results show that the magnetic flux from our designed electrical magnate in the range of (0.013- 0.08) Tesla and 30 minut

Non thermal argon plasma needle at atmospheric pressure was constructed. The experimental set up was based on simple and low cost electric components that generate electrical field sufficiently high at the electrodes to ionize various gases which flow at atmospheric pressure. A high AC power supply was used with 9.6kV peak to peak and 33kHz frequency. The plasma was generated using two electrodes. The voltage and current discharge waveform were measured. The temperature of Ar gas plasma jet at different gas flow rate and distances from the plasma electrode was also recorded. It was found that the temperature increased with increasing frequency to reach the maximum value at 15 kHz, and that the current leading the voltage, which demonstra

This search study the effect of particle size of graphite on the mechanical and thermal properties of epoxy composites, where graphite adopted with particle sizes (45,53,75) ?m, respectively, and the percentages by weight (0,1,3,5,7,9)% for each size of this three particle sizes.Mechanical properties represented by the bending (three-point bending) and through which the conclusion is bending stress and modulus of elasticity, thermal properties were either through thermal conductivity tests.The results showed that the ratio(1%) is the maximum value of bending stress at the three particle size and the (45 ?m) is the maximum.Thermal conductivity result show is the maximum value at ratio (1%) of particle size(53 ?m)

The aim of this work is to produce samples from Iraqi raw materials like Husyniat Bauxite (raw and burnt) and to study the effect of some additives like white Doekhla kaolin clays and alumina on that material properties were using sodium silica as a binding material. Five mixtures were prepared from Bauxite (raw and burnt) and kaolin clays, with an additive of (40) ml from sodium silica and alumina of (2.5, 5, 7.5,10 wt %) percentage as a binding material. the size grading was through sieving. The formation of all specimens was conducted by a measured gradually semi-dry pressing method under a compression force of (10) Tons and humidity ratio ranging from (5-10) % from mixture weight. Drying all specimens was done and then they were burn