In this paper the effects of the contact material on the photovoltaic (PV) characteristics of p-NiO:Au/n-Si solar cells fabricated by using the pulsed laser deposition (PLD) technique had been studied. It shown the p-NiO:Au/n-Si could be successfully used to construct and improve the performance of solar cells by using Au. The conversion efficiency was increased comparable with p-NiO/n-Si solar cells. In this case the NiO:Au layer acts as a hole collector as well as a barrier for charge recombination.

The sequence in the upper part of the Balambo Formation is composed mainly of limestone alternating with marly limestones and dark grey shale in the Bosheen section (eastern Sulaymaniyah, northeastern Iraq) and has been studied in terms of its rare earth element (REE) content. The REEs are very low compared to modern marine sediments. They are depletion in LREEs, and enrichment in HREEs and (La/Yb)_N in the studied rocks, indicating that these sediments retained the REEs pattern of marine waters. The negative Ce anomaly reflects direct sedimentation from marine waters under anoxic conditions with the contribution of terrigenous clays. The positive correlation of ∑REEs with Al, Ti, and Y, and the negative correlation of ∑REE

In this paper, CdS/Si hetrojunction solar cell has been made by
Chemical Bath Deposition (CBD) of CdS thin film on to
monocrystalline silicon substrate. XRD measurements approved that
CdS film is changing the structure of CdS films from mixed
hexagonal and cubic phase to the hexagonal phase with [101]
predominant orientation. I-V characterization of the hetrojunction
shows good rectification, with high spectral responsivity of 0.41
A/W, quantum efficiency 90%,and specific detectivity 2.9*1014
cmHz1/2W -1 .

The chemical bath deposition technique (CBD) is considered the cheapest and easiest compared with other deposition techniques. However, it is highly sensitive to effective parameter deposition values such as pH, temperature, and so on. The pH value of the reaction solution has a direct impact on both the nucleation and growth rate of the film. Consequently, this study presents a novel investigation into the effect of a precise change. in the pH reaction solution value on the structural, morphological, and photoresponse characteristics of tin monosulphide (SnS) films. The films were grown on a flexible polyester substrate with pH values of 7.1, 7.4, and 7.7. The X-ray diffraction patterns of the grown films at pH 7.1 and 7.4 confirmed

In the recent decade, injection of nanoparticles (NPs) into underground formation as liquid nanodispersions has been suggested as a smart alternative for conventional methods in tertiary oil recovery projects from mature oil reservoirs. Such reservoirs, however, are strong candidates for carbon geo-sequestration (CGS) projects, and the presence of nanoparticles (NPs) after nanofluid-flooding can add more complexity to carbon geo-storage projects. Despite studies investigating CO2 injection and nanofluid-flooding for EOR projects, no information was reported about the potential synergistic effects of CO2 and NPs on enhanced oil recovery (EOR) and CGS concerning the interfacial tension (γ) of CO2-oil system. This study thus extensively inves

Diamond-like carbon (DLC) homogeneous thin films were deposited from cyclohexane (Ccyclohexane (Ccyclohexane (Ccyclohexane (C cyclohexane (Ccyclohexane (Ccyclohexane (C cyclohexane (Ccyclohexane (C 6H12 ) liquid by using a plasma jet system which operates with alternating high voltage 7.5 which operates with alternating high voltage 7.5which operates with alternating high voltage 7.5which operates with alternating high voltage 7.5 which operates with alternating high voltage 7.5which operates with alternating high voltage 7.5which operates with alternating high voltage 7.5 which operates with alternating high voltage 7.5which operates with alternating high voltage 7.5 which operates with alternating high voltage 7.5which operates with al

Burnishing improves fatigue strength, surface hardness and decrease surface roughness of metal because this process transforms tensile residual stresses into compressive residual stresses. Roller burnishing tool is used in the present work on low carbon steel (AISI 1008) specimens. In this work, different experiments were used to study the influence of feed parameter and speed parameter in burnishing process on fatigue strength, surface roughness and surface hardness of low carbon steel (AISI 1008) specimens. The first parameter used is feed values which were (0.6, 0.8, and 1) mm at constant speed (370) rpm, while the second parameter used is speed at values (540, 800 and 1200) rpm and at constant feed (1) mm. The results of the fatigue

     This research deals with a 2D seismic structural and stratigraphic interpretation of Khan Al-Baghdadi area which is located in the western part of Iraq in Anbar governorate. Two main seismic reflectors are identified within the Silurian and Ordovician; these are the Hot_shale_1 within Akkas Formation and the Top Khabour Formation, which were deposited during the Paleozoic, based on synthetic seismogram of Akk_3 well near the study area. Time, depth, and velocity maps show the presence of two anticline structures trending east-west and located on the west side of the study area. The first is the Tulul structure (here denoted as A) and the second is denoted as B. Also, the maps show the increase in time towards the

Most of the world's drilling companies use API method for calculating the
pressure drop in drilling oil and gas wells. Iraqi Drilling Company also uses this
method for drilling oil wells in all fields of Iraq. In Russia, the method is actively
used Grodde for calculating the pressure drop in drilling oil and gas wells. This
study includes a comparison of formulas API, Grodde and new techniques
developed methods for the laminar flow of viscoplastic fluids in the annular space.
The aim of this study is to determine the most accurate way to calculate the pressure
loss in drilling oil wells. The comparison was focused on identifying changes in the
values of β, using the above calculation methods.

A simple, inexpensive, and home–built electrostatic spray deposition (ESD) system with stable cone-jet mode was used to obtain nickel oxide (NiO) thin films on glass substrates kept at temperature of 400°C. The primary precursor solution of 0.1 M concentration hydrated nickel chloride dissolved in isopropyl alcohol. The structural, optical and electrical parameters were studied. The optical absorbance spectra for the studied samples showed its maximum around 280 nm. On the other hand, thickness interferometry measurements on the tested samples showed that film thickness was around 400 nm. The optical energy gap of the prepared NiO samples was determined to be 3.75 eV and the maximum value of refractive index was determined to be 2.1 a