An analytical approach based on field data was used to determine the strength capacity of large diameter bored type piles. Also the deformations and settlements were evaluated for both vertical and lateral loadings. The analytical predictions are compared to field data obtained from a proto-type test pile used at Tharthar –Tigris canal Bridge. They were found to be with acceptable agreement of 12% deviation.

               Following ASTM standards D1143M-07e1,2010, a test schedule of five loading cycles were proposed for vertical loads and series of cyclic loads to simulate horizontal loading .The load test results and analytical data of 1.95

    The cutting transport problem in the drilling operation is very complex because many parameters impact the process, which is nonlinearity interconnected. It is an important factor affecting time, cost and quality of the deviated and horizontal well. The main objective is to evaluate the influence of main drilling Parameters, rheological properties and cuttings that characterise lifting capacity through calculating the minimum flow rate required and cutting bed height and investigate these factors and how they influenced stuck pipe problems in deviated wells for Garraf oil field. The results obtained from simulations using Well Plan™ Software were showed that increasing viscosity depends on other conditions for an increase or dec

The polygamy as a social was known before Islam, has kept Islam on this system after it organized and put his controls and conditions, as justice between wives and the ability to alimony, it was not the purpose of satisfying the instinct of man and enjoyment, but his goal nominal than that, because it addresses problems humanity has goals noble, so the pluralism overlap of the fabric of families belonging to governance and benefits for women and men and society, which leads to increased ties of love between people of the same society and thus increases the cohesion and importance of the topic and its association with financial conditions have emerged as needed so you viewed in the second scientific Conference of the Department social Ser

This study deals with the seismic reflection interpretation of Cretaceous Formations in Tuba oil field, southern Iraq, including structural and stratigraphic techniques. The study achieved by using Geofram , Geolog and Petrel software. The interpretation process, of 2-D seismic data and well logs have been used. Based on well logs and synthetic traces two horizons were identified and picked which are the tops of Mishrif and Zubair Formations. These horizons were followed over all the area in order to obtain their structural setting. Structural interpretation indicates that the Tuba oil field is an anticline structure as well as the presence of normal fault near Mishrif Formation trending NE-SW. Information from the wells appeared Mishrif

An optimization analysis of drilling process constitutes a powerful tool for operating under desired pressure levels and simultaneously maximizing the penetration rate, which reduces costs and time thus increases the profit.
In this study, a composite drilling model (Young-Bourgyen model) of eight functions was used to determine the optimum drilling mechanical parameters (Weight on bit and rotary speed) for an Iraqi oil field. These functions model the effect of most drilling parameters such as formation strength, mud density, formation compaction, weight on bit, rotary speed, tooth dullness, and bit hydraulic on drilling rate. Data are extracted from bit record and drilling report of well BUZ-20 for calculation of eight exponents of

This paper is carried out to detect the subsurface structures that have geological
and economical importance by interpreting the available reflection seismic data of
an area estimated to be about (740) km2. The Khashim Al-Ahmer structure is partial
of series structures of (Injana – Khashim Al-Ahmer – Mannsorya) from the (NW to
the SE), it is located within for deep faulted area. The component of the one
elongated dome of asymmetrical of structure which has(SW) limb more steeper than
the (NE) limb.Twenty three seismic sections had been interpreted for two seismic
surveys and the total length of all seismic lines is about (414.7) Km. Interpretation
of seismic data was focused on two reflectors (Fatha and Jeribi)

Petrophysical properties of Mishrif Formation at the Tuba field determined from interpretation of open log data of(Tu-2,3,4,5,6,12,24,and 25) wells. These properties include total (effected) and secondary porosity, as well as moveable and residual oil saturation into invaded and uninvaded zones. According to Petrophysical properties it is possible to divided Mishrif Formation into three reservoir units (RU1,2,and 3) separated by four cap rocks (Bar1,2,3,and 4) . Three-dimension reservoir model is established by used (Petrel, 2009) Software for each reservoir units. Result shows that the second and third reservoir units represent important reservoir units of Mishrif Formation. Thickness and reservoir properties enhanced toward middle and

Abstract

 Metal cutting processes still represent the largest class of manufacturing operations. Turning is the most commonly employed material removal process. This research focuses on analysis of the thermal field of the oblique machining process. Finite element method (FEM) software DEFORM 3D V10.2 was used together with experimental work carried out using infrared image equipment, which include both hardware and software simulations. The thermal experiments are conducted with AA6063-T6, using different tool obliquity, cutting speeds and feed rates. The results show that the temperature relatively decreased when tool obliquity increases at different cutting speeds and feed rates, also it

Geologic modeling is the art of constructing a structural and stratigraphic model of a reservoir from analyses and interpretations of seismic data, log data, core data, etc. ‎[1].

   A static reservoir model typically involves four main stages, these stages are Structural modeling, Stratigraphic modeling, Lithological modeling and Petrophysical modeling ‎[2].

   Ismail field is exploration structure, located in the north Iraq, about 55 km north-west of Kirkuk city, to the north-west of the Bai Hassan field, the distance between the Bai Hassan field and Ismael field is about one kilometer ‎[3].

   Tertiary period reservoir sequences (Main Limestone), which comprise many economica

Carbonate matrix stimulation technology has progressed tremendously in the last decade through creative laboratory research and novel fluid advancements. Still, existing methods for optimizing the stimulation of wells in vast carbonate reservoirs are inadequate. Consequently, oil and gas wells are stimulated routinely to expand production and maximize recovery. Matrix acidizing is extensively used because of its low cost and ability to restore the original productivity of damaged wells and provide additional production capacity. The Ahdeb oil field lacks studies in matrix acidizing; therefore, this work provided new information on limestone acidizing in the Mishrif reservoir. Moreover, several reports have been issued on the difficulties en