Digital Elevation Model (DEM) is one of the developed techniques for relief representation.  The definition of a DEM construction is the modeling technique of earth surface from existing data. DEM plays a role as one of the fundamental information requirement that has been generally utilized in GIS data structures. The main aim of this research is to present a methodology for assessing DEMs generation methods. The DEMs data will be extracted from open source data e.g. Google Earth. The tested data will be compared with data produced from formal institutions such as General Directorate of Surveying. The study area has been chosen in south of Iraq (Al-Gharraf / Dhi Qar governorate. The methods of DEMs creation are kriging, IDW (inver

Ab – initio density function theory (DFT) calculations coupled with Large Unit Cell (LUC) method were carried out to evaluate the electronic structure properties of III-V zinc blend (GaAs). The nano – scale that have dimension (1.56-2.04)nm. The Gaussian 03 computational packages has been employed through out this study to compute the electronic properties include lattice constant, energy gap, valence and conduction band width, total energy, cohesive energy and density of state etc. Results show that the total energy and energy gap are decreasing with increase the size of nano crystal . Results revealed that electronic properties converge to some limit as the size of LUC increase .

The placement of buildings and structures on/or adjacent to slopes is possible, but this poses a danger to the structure due to failures that occur in slopes. Therefore, a solution or improvement should be determined for these issues of the collapse of the structure as a result of the failure of the slopes. A laboratory model has been built to test the impact of some variables on the bearing capacity factor. The variables include the magnitude of static axial load applied at the center of footing, the depth of embedment, the spacing between geogrid reinforcement layer and the numbering of the geogrid sheet under the footing, the inclination angle of slope clayey soil (β), the spacing between the footing's edge and the slope's end (b/H). Th

In this paper, we define a cubic bipolar subalgebra, $BCK$-ideal and $Q$-ideal of a $Q$-algebra, and obtain some of their properties and give some examples. Also we define a cubic bipolar fuzzy point, cubic bipolar fuzzy topology, cubic bipolar fuzzy base and for each concept obtained some of its properties.

PDBN Rashid, International Journal of Development in Social Sciences and Humanities, 2023

Praise be to God, Lord of the worlds, and prayers and peace be upon our master Muhammad and upon his family and companions.
And after:

      Muslim scholars have fought in the extent of regard to these interests, each according to his opinion and according to his evaluation, and his consideration of this interest, but it remains important that the legislation in them needs more precaution and caution against the predominance of passions, because the passions often decorate spoilers so they see an interest, so practical application must To realize the spirit of Islamic Sharia in its entirety of its rulings, and the preponderance between the interests and evils that prevail in our societies, which c

          The effect of acute toxicity of chromium as (k2Cro4) on Simocephalus  expinosus (cladocera) and Mesocyclops hyalinus (cyclopoida) was studied in the present study .Both species can be used as asutible biological indecaters. In addition  Both of them are part of crustacean zooplankton.Their position in the fresh water  food chain, as the cladocerans constitutes the primary consumers while cyclopoids are part of secondary consumers.         To determine LC50 of chromium for the two species the following concentrations  of chromium  were  used 1,2, 3,4, 5,6, 14,18, 22,26,28, and 30 ppm. The results showed that LC 50 o

This study was undertaken to provide more insight on the optimum injection temperature used for the production of PE crates, thereby saving time and money, and improving part quality. The work included processing trails of HDPE crates in an injection
molding machine at five temperatures ranged from 220 to 300°C. Both Rheological and mechanical characterization was conducted in order to understand the effect of injection temperature on the properties of crates. Oven aging was also applied for (4 weeks) to evaluate the long-term thermal stability. The results revealed that producing the crates at a temperature range of (260-280 °C) gives the best rheological and mechanical result. The lowest drop in thermal stability has been observed