the energy that a radiation source emits as light (photons), electromagnetic waves, or particles is known as radiation. X-ray is one type of ionizing radiation that falls within the electromagnetic wave category of short wavelengths. Because of their short wavelength. X-ray is a type of ionizing radiation that is used in a constantly growing number of diagnostic procedures. X-ray diagnostic imaging has been employed in the medical field for more than a century(Hariyoto et al., 2020). Radiation has advantages for human health, but there is also a risk. the impacts of Radiation on Fertility it is an oligospermia, or a reduction in the number of sperm cells, which is already possible after radiation exposure of 0.15 mGy. It Leads to impedes the process of generating the resultant sperm cell through a deterministic effect. (Tuieng et al., 2021). Infertility affects 1 in 6 couples globally. Nearly 50% of infertility cases are caused by male causes. Although low sperm counts, abnormal sperm morphology, and impaired sperm motility are recognized causes, the underlying reasons remain unknown in 25% of instances.(Inhorn and Patrizio, 2014). Human infertility is reliant on the meiotic process, which leads to the development of germ cells. This procedure is extremely radiation-sensitive. the relationship between radiation exposure and infertility is thought to originate from DNA damage induced by free radicals originating from radiation ionization. DNA damage might cause some mutations or cause cell death (apoptosis). (Skrzypek et al., 2019) Even though X-rays are one of the most common diagnostic instruments used on patients, not much study has been done on the impacts of X-ray exposure on medical workers. One condition that is commonly observed in medical workers who are exposed to radiation regularly is infertility. For the diagnosis of many illnesses, radiodiagnosis tools like C-ARM, and CT-SCAN. X-rays are still the mainstay. Frequent usage of small amounts of X-ray radiation can have an accumulating effect that results in other abnormal epigenetic patterns and DNA damage. To reduce the radiation exposure of medical workers, further study is required to find the best X-ray doses, times, and saf
Inefficient wastewater disposal and wastewater discharge problems in water bodies have led to increasing pollution in water bodies. Pollutants in the river contribute to increasing the biological oxygen demand (BOD), total suspended solids (SS), total dissolved solids (TDS), chemical oxygen demand (COD), and toxic metals render this water unsuitable for consumption and even pose a significant risk to human health. Over the last few years, water conservation has been the subject of growing awareness and concern throughout the world, so this research focused on review studies of researches that studied the importance of water quality of wastewater treated disposal in water bodies and modern technology to management w
... Show More
(2)
Fourier Transform-Infrared (FT-IR) spectroscopy was used to analyze gasoline engine oil (SAE 5W20) samples that were exposed to seven different oxidation times (0 h, 24 h, 48 h, 72 h, 96 h, 120 h, and 144 h) to determine the best wavenumbers and wavenumber ranges for the discrimination of the oxidation times. The thermal oxidation process generated oil samples with varying total base number (TBN) levels. Each wavenumber (400–3900 cm−1) and wavenumber ranges identified from the literature and this study were statistically analyzed to determine which wavenumbers and wavenumber ranges could discriminate among all oxidation times. Linear regression was used with the best wavenumbers and wavenumber ranges to predict oxidation time.
... Show More
(20)
(19)
Accurate calculation of transient overvoltages and dielectric stresses from fast-front excitations is required to obtain an optimal dielectric design of power components subjected to these conditions, which are commonly due to switching and lightning, as well as utilization of power-electronic devices. Toroidal transformers are generally used at the low voltage level. However, recent investigations and developments have explored their use at the medium voltage level. This paper analyzes the model-based improvement of the insulation design of medium voltage toroidal transformers. Lumped and distributed parameter models are used and compared to predict the transient response and dielectric stress along the transformer winding. The parameters
... Show More
(1)
(18)
(11)
(14)
(15)
(4)
(13)
(31)
(1)
(1)
Pultruded materials made of Fiber-Reinforced Polymer (FRP) come in a broad range of shapes, such as bars, I-sections, C-sections, etc. FRP materials are starting to compete with steel as structural materials owing to their great resistance, low self-weight, and cheap maintenance costs, especially in corrosive conditions. This study aims to evaluate the effectiveness of a novel concrete Composite Column (CC) using Encased I-Section (EIS) as a reinforcement in contrast to traditional steel bars by using Glass Fiber-Reinforced Polymer (GFRP) as I-section (CC-EIS) to evaluate the effectiveness of the hybrid columns which have been built by combining GFRP profiles with concrete columns. To achieve the aims of this study, nine circular co
... Show More
(4)
(3)