Milling Machining is a widely accepted nontraditional machining technique used to produce parts with complex shapes and configurations. The material is removed in two stages roughing and finishing, the flat end cutter removed the unwanted part of material, then finished by end mill cutter. In milling technique, the role of machining factors such as cutting depth, spindle speed and feed has been studied using Taguchi technique to find its effectiveness on surface roughness. Practical procedure is done by Taguchi Standard matrix. CNC milling is the most conventional process which is used for removing of material from workpiece to perform the needed shapes. The results and relations indicate that the rate of feed is very important factor for modeling surface roughness. The plot of S/N ratio shows that the optimum combination of the milling factors that gives the best value of surface accuracy. The best combination of milling factors has also been predicted to minimize the surface roughness.
This research study the effect of Titanium dioxide on the tensile properties of
Polystyrene (PS) and Polycarbonate (PC) polymers. The stress – strain curve for pure PS
and pure PC, shows that Young modulus for PS is higher than Young modulus for PC,
because PS have higher ultimate strength than PC.
The addition of TiO2 to PS and PC will reduce the Young modulus and ultimate stress,
because the TiO2 particles will reduces or freeze the orientation of these molecular chain
and reduced the toughness of PC, while when the TiO2 were added to PS, the value of
toughness will be stabilized because TiO2 particles make these chains interlocked and the
mobility of the chains will be restrict.
The performance of photovoltaic (PV) panel having staggered metal foam fins was examined experimentally in Baghdad, Iraq. Three staggered metal foam fin configurations attached to the backside of the PV panel were studied. The measured parameters were front and back surfaces temperature, open voltage and current circuits, maximum power, and PV efficiency. It was noted that the maximum electrical efficiency enhancement was 4.7% for staggered metal foam fins (case III) than the reference PV panel. The operating temperature of the cell was increased when the value of solar intensity was high. Thereby, the electrical efficiency was decreased. It was found that the metal foam fins decreased the PV temperature by 2-3 o
... Show MoreCompaction of triticale grain with three moisture contents (8%, 12%, and 16% wet basis) was measured at five applied pressures (0, 7, 14, 34, and 55 kPa). Bulk density increased with increasing pressure for all moisture contents and was significantly (p < 0.0001) dependent on both moisture content and applied pressure. A Verhulst logistic equation was found to model the changes in bulk density of triticale grain with R2 of 0.986. The model showed similar beha
A 3D geological model is an essential step to reveal reservoir heterogeneity and reservoir properties distribution. In the present study, a three-dimensional geological model for the Mishrif reservoir was built based on data obtained from seven wells and core data. The methodology includes building a 3D grid and populating it with petrophysical properties such as (facies, porosity, water saturation, and net to gross ratio). The structural model was built based on a base contour map obtained from 2D seismic interpretation along with well tops from seven wells. A simple grid method was used to build the structural framework with 234x278x91 grid cells in the X, Y, and Z directions, respectively, with lengths equal to 150 meters. The to
... Show More(فتح الرحمن بكشف ما يلتبس في القرآن ) لزكريا الأنصاري (ت 926 هـ ) مصنَّف مهم تبارت فيه علوم العربية لفكّ ما يثيره ظاهر آيات قرآنية من لبس لدى المتلقي ، فكان للبلاغة السطوة في ذلك ، ولأهميته طبع طبعات كثيرة ، خمس منها بتحقيق محمد علي الصابوني ، وهو التحقيق المهمين الشائع ، غيرأنه لم يستوفِ الأسلوب العلمي في اخراج النصوص، إذ بدت فيه مزالق كثيرة بينَ تغيير وسقط ووهم وتحريف وتصحيف ودمج مما استنهض فكرة هذا البحث ، للتنب
... Show MoreThe aim of this research is to study the effect of using computer
techniques to increase students information at the experimenting the speed
control of dc motor by the magnetic field.
Simulation of the experiment has been used by implementing
“Electronics Workbench” software.
The random sample, included (30) second year electrical department
students, divided into two groups , experimental and control with pre-test and
post-test .
The results showed great advantages for the experimental group
through the use of computer program in the laboratory. The calculated (t) was
(10.6) which was significant and showed statistical differences between the
experimental and control group.
According to the result
تواجه الوحدات الاقتصادية في العراق منافسة قوية بسبب مشكلات خاصة بإرتفاع الاسعار وارتفاع تكاليف الانتاج وضعف الاهتمام بدراسة السوق وغيرها من المشاكل ، فضلاً عن استخدام نظام التكاليف التقليدي الذي لا يوفر معلومات ملائمة لقرارات التسعير الامر الذي يتطلب دراسة وتحليل تلك المشكلات ومعالجتها بالاعتماد على تقنيات حديثة بما يمكنها من المنافسة ولهذا جاء هذا البحث والذي يعتبر من المداخل الحديثة لتخفيض التكاليف وم
... Show More