Abstract

The environmental conditions are important factors, because they affect both the efficiency of a photovoltaic module and the energy load. This research was carried out experimentally and modeling was done in MATLAB –Simulink by monitoring the variation in power output of the system with environmental conditions such as solar radiation, ambient temperature, wind speed, and humidity of Baghdad city. From the results, the ambient temperatures are inversely proportional to humidity and the output power performance of the system, while the wind speed is directly proportional with the output power performance of the system.  

Keywords:

The economical design of plate loaded by pressure can be obtained by using stiffeners instead of increasing the thickness of plate. The main subject of this work is to obtain the effect of stiffener height on the maximum stress in the plate subjected to pressure load. Different plate-stiffener sets are selected to find the effects of stiffener thickness, plate dimensions and pressure, on the optimum stiffener height. The models under consideration are square plates clamped rigidly from four edges. Finite Element method is used to analyze 160 different models by using the Finite Element software package ANSYS version 11. Another analysis method based on maximum stress equation is used to analyze 30 models. The graphical comparison of results

Reinforced concrete barriers have been commonly used in protecting the important building because the response of R.C. barriers subjected to blast loading is practically more acceptable than other materials used to build the barriers. In this study, the response of R.C. barriers was detected due to the blast effects caused by two charge weights (50 kg and 400 kg); ANSYS 14 was used to simulate the problem. A horizontal distance of 2 m between the explosive TNT charge and the front face of wall was taken. The pressure on the front face of the concrete barriers was measured at three levels. The R.C. barrier was entirely damaged when subjected to the blast effects caused by 400 kg TNT explosion bomb. However, the 50 kg TNT charge had

               This paper studies the effect of the solar indices (total sunspot no., solar wind density and coronal mass ejection linear speed) on F₂- layer electron density, as well as, the comparison of seasonal variations of electron density of F₂- layer, N_mF₂, for Mars at local noontime and for maximum and minimum solar cycles.                  

 Results show that there is an inverse correlation between sunspot number, solar wind density, CME linear speed and ionosphere electron density for Mars, at maximum and minimum solar cycles. This correlation is clear when electron density is at minimum value.                          

Before setting a turbine in a wind farms allocated for power generation, it must be know the appropriate turbine class for that site depending on the turbulence intensity of the winds in the studied area and the IEC-61400 standard. The importance of identifying a class of wind turbine is due to the complex environmental conditions that produce turbulent air which, in turn, may cause damage to the turbine blades and weakness in the performance. Therefore, the ambient turbulence intensity is a very important factor in determining the performance and productivity of the wind turbines.
In this research we calculate Turbulence Intensity "TI" in the province of Nasiriyah, south of Iraq (Lat. 31.052049 , Lon. 46.261021) for the years 2008, 2

The present work describes the adsorption of Ba2+ and Mg2+ions from aqueous solutions by activated alumina in single and binary system using batch adsorption. The effect of different parameters such as amount of alumina, concentration of metal ions, pH of solution, contact time and agitation speed on the adsorption process was studied. The optimum adsorbent dosage was found to be 0.5 g and 1.5 g for removal of Ba2+ and Mg2+, respectively. The optimum pH, contact time and agitation speed, were found to be pH 6, 2h and 300 rpm, respectively, for removal of both metal ions. The equilibrium data were analyzed by Langmuir and Freundlich isotherm models and the data fitted well to both isotherm modes as indicated by higher correlation of deter

Seismic instantaneous phase attribute was applied for conventional seismic interpretation (structural interpretation) on 3D seismic cube of 1914.72km² of Samawa-Diwan area, located in the south part of Iraq within Muthna governorate. Instantaneous phase section is very important to detect structural and stratigraphic features. Six reflectors represent Upper Jurassic and Cretaceous formations were defined from synthetic seismogram of wells in study area, then picked over seismic cube. Fault boundaries maps for each horizon were drawn depending on horizon contacts then fault planes were constructed. Finally, a 3D structural model was constructed in time domain, then converted to depth domain by using 3D average velocity model. Structurall

In this paper a refractive index sensor based on micro-structured optical fiber has been proposed using Finite Element Method (FEM). The designed fiber has a hexagonal cladding structure with six air holes rings running around its solid core.  The air holes of fiber has been infiltrated  with different liquids such as water , ethanol, methanol, and toluene then sensor characteristics like ; effective refractive index , confinement loss, beam profile of the fundamental mode, and sensor resolution are investigated by employing the FEM. This designed sensor characterized by its low confinement loss and high resolution so a small change in the analyte refractive index could be detect which is could be useful to detect the change of

In the framework of correlation method so-called coherent density fluctuation model (CDFM) the nucleon momentum distributions (NMD) of the ground state for some even mass nuclei of fp-shell like 50Cr, 52Cr and 54Cr isotopes are examined. Nucleon momentum distributions are expressed in terms of the fluctuation function (|f(x)|2) which is evaluated by means of the nucleon density distributions (NDD) of the nuclei and determined from theory and experiment. The main characteristic feature of the NMD obtained by CDFM is the existence of high-momentum components, for momenta k ≥ 2 fm−1. For completeness, also elastic electron scattering form factors, F(q) are evaluated within the same framework.