Nano particles of Cadmium Oxide (CdO) thin films were prepared by spray pyrolysis technique. The synthesized film is annealed at (200 , 300, 450) o C for 3 hours .  The XRD and AFM for the analysis of its structural and micro-structural characteristic has been preformed. The average grain size was found to be about 32.50 nm .There is a preferred orientation along (200)   plane  with texture coefficient 1.79, 1.644, 1.763 and 1.792  for deposited and annealed films, corresponding to grain size 57,58 ,51 and 51 nm. The variations of stress with temperature is ranged from 0.157 - 0.376 GPa .
 

This research studies Reinforcing and applied load of  Wear Rate for Epoxy composites contains from epoxy resin (Ep) as a matrix material and reinforced by Gawain red wood flour , Russian white wood flour , glass powder and rock wool fibers , with volume fraction (20%) for all samples in lab conditions.  by using the load (10,20 ,30 ,40) Newton of iron disc for testing  time(10) minute, and the results have shown that the reinforcing of epoxy resin led to decrease  wear rate for all samples except the hybrid composites reinforced earth glass powder , that the wear rate values  decrease  from   (22×10-9g/cm) to (4×10-9g/cm) of composite material(Ep+R.W.F) and thus(Ep+W.W.F)   at la

Different polymers were prepared by condensation polymerization of sebacic anhydride and adipic anhydride with ethylene glycol and poly(ethylene glycol). Their number average molecular weights were determined by end group analysis. Then, they were grafted on the prepared phthalocyaninatocopper(II) compounds with the general formula (NH2)4PcCu(II) having amino groups of 3,3',3'',3'''- or 4,4',4'',4'''- positions. All prepared polymers, compounds, and phthalocyaninatocopper(II)-grafted polymers were characterized by FTIR. The sizing measurements were carried out in 3,3',3'',3'''- (NH2)4PcCu(II) and 4,4',4'',4'''- (NH2)4PcCu(II) compounds with and without grafting polymers. The results showed that the grafting process led to decreasing in par

The aim of this research is to design and construct a semiconductor laser range finder
operating in the near infrared range for ranging and designation. The main part of the range finder is the
transmitter which is a semiconductor laser type GaAs of 0.904 mm wavelength with a beam expander,
and the receiver with its collecting optics. The characteristics of transmitter pulse width were 200ns and
threshold current 10 Amp. and maximum operating current 38 Amp. The repetition rate was set at 660 Hz
and maximum output power about 1 watt. The divergence of the beam was 0.268o. A special computer
code was used for optimum optical design and laser spot size analysis and for calculation of atmosphere
attenuation.

Background: prednisolone is a corticosteroid with a very bitter taste acts as anti- anti-inflammatory and immune suppressant drug and it is used at any age.

Objective: To improve patient compliance by masking the bitter taste of the drug to be delivered as an orodispersible tablet.

Methods: External ionic gelation using sodium alginate (0.5%w/v) and calcium chloride (1% w/v) in presence of 0.5% w/v carbopol 940 was used to prepare taste masked beads loaded with prednisolone to be compressed as orodispersible tablets.  

Results:  The bitter taste of was masked by preparing beads composed of 1:1:1 (sodium alginate: Carbopol 940: prednisolone) which r

Seven strains of Rhizobium leguminosarum bv. vicide were isolated
and purified from the root nodules of faba bean (Viciae faba) plants
collected from different agroclimatic locations in Baghdad and Diyala
provinces of Iraq. Screening of these strains gives four salinity tolernat  strains which tolerate 1-5% sodium chloride supplement mannitol to  salt yeast extract (M Y) medium. Colony forming units for the four tolerant strains under stress conditions were significantly reduced in comparison with those under normal conditions. Different tests were used to study the surface properties of stress tolerant strains under  normal and stress conditions. No differences were found in the production of lipopolysaccharid

Stream of Consciousness technique has a great impact on writing literary texts in the modern age. This technique was broadly used in the late of nineteen century as a result of thedecay of plot, especially in novel writing. Novelists began to use stream of consciousness technique as a new phenomenon, because it goes deeper into the human mind and soul through involving it in writing. Modern novel has changed after Victorian age from the traditional novel that considers themes of religion, culture, social matters, etc.  to be a group of irregular events and thoughts interrogate or reveal the inner feeling of  readers.

This study simplifies stream of consciousness technique through clarifying the three levels of conscious

الخلاصة لقد شكل المحافظون الجدد وهم بالأساس نخبة من المثقفين ومن السياسيين الأمريكيين كتلة ضغط كبيرة التأثير على الإدارة في عهد الجمهوريين. حمل هؤلاء المحافظون مشروعاً إيديولوجياً البسوه لسلطة الجمهوريين وهو يهدف إلى جعل أمريكا سيدة العالم من دون منازع خاصة بعد انهيار الاتحاد السوفييتي ونهاية الحرب الباردة. واكب هذا الحدث التاريخي الكثير من الأفكار ومنها (نهاية التاريخ)، وصراع الحضارات، وكذ

The political participation of the Iraqi woman, gains a big importance equivalent to its role in all other fields. Therefore , it represents a higher value in the democratic orientation in addition to the importance of rising the reality of the woman specifically in the fields that are considered as a scale of the human development like the income, health, and education . The weakness of womenʹs political participation, is something that can't be ignored or neglected if we are looking forward to the rising of the country᾽s reality and achieving the required development in its all aspects. The woman is half of society or more than that due to the burden of raising the generations tasks. This can be achieved by taking part in th

In the present work usedNd:YAG laser systems of different output characteristic were employed to study the drilling process of material used in scientific and industrial fields. This material include Manganese hard steel. Our study went into the affecting parameters in drilling of Manganese hard steel by laser. Drilling process is achieved through material absorption of part of the incident laser beam. It is the resultant of interfering both, laser beam and material properties and the focusing conditions of the beam. The results as shown that the increase in the laser pulse energy over the used level has raised the hole diameter, depth and increased the hole taper. In addition to that a hole taper was affected by the laser energy, the fo