This study appears GIS techniqueand remote sensing data are matching with the field observation to identify the structural features such as fault segments in the urban area such as the Merawa and Shaqlawa Cities. The use of different types of data such as fault systems, drainage patterns (previously mapped), lineament, and lithological contacts with spatial resolution of 30m was combined through a process of integration and index overlay modeling technique for producing the susceptibility map of fault segments in the study area. GIS spatial overlay technique was used to determine the spatial relationships of all the criteria (factors) and subcriteria (classes) within layers (maps) to classify and map the potential area of geological outcrops and fault zones of the study area. The fault segments map appears that there is well correlation and distribution between fault segments and fault systems in the study area.There are dozens of fault segments which may represent new faults in the area being identified. The presence of these faults is not known from the literature. These fault systems could be active due to the convergent system of the closure of new Tethys and building of Zagros belt. Active or reactivated faults can cause enormous damage to settlement (houses or construction project) areas by rock mass movement along the fault surfaces or bedrock cracks, damage which refers to loss of life or injury, or damage to roads. Furthermore, updated the maps and old study create new ones using new data and techniques and advise the people about the proper sitting of houses and restricting settlement activities in danger areas. GIS models can then yield more accurate estimates of the fault mapping using more data such as geophysical data.
Magnesium oxide nanoparticles were synthesized via a co-precipitation procedure. Comprehensive characterization included infrared fluorescence, X-ray scattering spectroscopy, scanning electron microscopy, as well as X-ray diffraction and atomic force microscopy. Surface properties were analyzed using Langmuir, Brunauer -Emmett-Teller, Barrett–Joyner–Halenda, t-plot techniques, and the N2 adsorption-desorption isotherms methods to determine surface area and pore structure. Results confirmed the nanoparticles possess high purity. The size of the synthesized particles ranged from 30-40 nm, which was determined by scanning electron microscopy. The surface area of the prepared particles is 31,227 m2 g-1, and it was found that the por
... Show More
Photonic Crystal Fiber Interferometers (PCFIs) are widely used for sensing applications. This work presents the fabrication and the characterization of a relative humidity sensor based on a polymer-coated photonic crystal fiber that operates in a Mach- Zehnder Interferometer (MZI) transmission mode. The fabrication of the sensor involved splicing a short (1 cm) length of Photonic Crystal Fiber (PCF) between two single-mode fibers (SMF). It was then coated with a layer of agarose solution. Experimental results showed that a high humidity sensitivity of 29.37 pm/%RH was achieved within a measurement range of 27–95%RH. The sensor also showed good repeatability, small size, measurement accuracy and wide humidity range. The RH sensitivity o
... Show MoreThe experimental and numerical analysis was performed on pipes suffering large plastic deformation through expanding them using rigid conical shaped mandrels, with three different cone angles (15◦, 25◦, 35◦) and diameters (15, 17, 20) mm. The experimental test for the strain results investigated the expanded areas. A numerical solution of the pipes expansion process was also investigated using the commercial finite element software ANSYS. The strains were measured for each case experimentally by stamping the mesh on the pipe after expanding, then compared with Ansys results. No cracks were generated during the process with the selected angles. It can be concluded that the strain decreased with greater angles of con
... Show More
(3)
(3)
(2)
(2)
(2)
Pulsed-laser deposition (PLD) technique was used to prepare thin films from cerium oxide (CeO2) doped with erbium and indium oxides. In order to characterize the morphology and sensing features, these films were deposited on glass and/or single silicon substrates, respectively, with erbium and indium oxides. The morphological investigation conducted using atomic force microscope has shown an increase in the non-regularity of particle diameter with increasing doping ratios of both oxides. The maximum particle diameter of 61.45nm was obtained for 9% Eu2O3-doped CeO2. The surface roughness value of Eu2O3-doped ceria was higher than those of In2O3-doped ceria. The gas sensing measurements were done at
... Show More The researcher was interested in studying a crucial aspect of the systematic world music culture. He highlights the analysis of the harmonic construction in the musical compositions of the artist Khalil Ismail, where harmony is a significant Western musical science, a pillar of the structure of instrumental and vocal music.
It depends on the compositions of vertical sounds performed simultaneously, as tones coincide and are sometimes dissonant to give sound resonance that enriches musical work and attracts recipients. Hence, the researcher has many questions, including: Can the composition of the writings of the artist Khalil Ismail determine in an objective research framework? Is there a study on this subject in some detail? whic
(3)
(5)
(4)