A groundwater quality assessment has been carried out in northeast part of Anbar governorate in western Iraq. We analyzed hydrochemical parameters such as pH, electrical conductivity, total dissolved solids presence of ions to describe groundwater quality. The study area has the only confined aquifer within the geological formation extended in area. Values of groundwater hydrochemical parameters were ranged from (7) to (7.9) for ph, (1599) to (6800) µmhos/cm for electrical conductivity (EC) and (1048) to (4446) mg/l for total dissolved solids (TDS). The origins and types of groundwater in the area were of marine origin and MgCl₂ water type while only (6) samples were of continental origin and Na₂SO₄ wate

Fusarium pseudograminearum and Fusarium graminearum commonly cause crown rot (FCR) and head blight (FHB) in wheat, respectively. Disease infection and spread can be reduced by the deployment of resistant cultivars or through management practices that limit inoculum load. Plants deficient in micronutrients, including zinc, tend to be more susceptible to many diseases. On the other hands, and zinc deficiency in cereals is widespread in Australian soils. Zinc deficiency may have particular relevance to crown rot, the most important and damaging Fusarium disease of wheat and barley in Australia. Four wheat genotypes; Batavia, Sunco and two lines from the International Maize and Wheat Improvement Center (CIMMYT) were tested for response

Through an experimental program of eighteen specimens presented in this paper, the bond strength between reinforcing bar and rubberized concrete was produced by adding waste tire rubber instead of natural aggregate. The fine and coarse aggregate was replaced in 0%, 25%, and 50% with the small pieces of a waste tire. Natural aggregate replacement ratio, rebar size, embedded rebar length, the rebar yield stress of rebar, cover, and concrete compressive strength were studied in this investigation. Ultimate bond stress, bond stress-slip response, and failure modes were presented. The experimental results reported that a reduction of 19% in bond strength was noticed in 50% replaced rubberized concrete compared with convention

Action films employ many artistic and literary elements that contribute greatly to building the general meaning of the film and push the wheel of the film forward. The element of mystery and suspense is used as two basic elements in action films. The cinematic language in action films depends on global coding, which is not models as it might be. It is based on logic, rather as units that aspire to morphology and not their homogeneity as the physical sense, but as the logical harmony of interpretive authority and enlightenment and in action films as a field of communication and a field in its origin in which the signifier contrasts with the perceptions of the meaning and in it takes a certain number of units preventing each other and thro

The aim of this study is to compare and contrast the science process skills (SPS) included in the 10th-12th grade physics textbooks content utilized in Yemeni schools. The study revealed weaknesses and strengths in the textbooks’ content. For instance, a number of science process skills (SPS), such as measuring, predicting and hypothesizing, have been neglected in the 11th grade textbook. For all three textbooks content, the maximum percentage of basic science process skills (BSPS) was devoted to observation. However, the maximum percentage of integrated science process skills (ISPS) was different for each grade: experimenting had the highest percentage for 10th grade, interpreting data for 11th grade, and operational definitions for 12th

The current study aimed to detect the effect of gentamicin stress on the expression of hla (encodes hemolysin) and nuc (encodes nuclease) genes of Staphylococcus aureus. Fifty-eight isolates identified as S. aureus were isolated locally from different clinical specimens. Disk diffusion method was used to detect the resistance to S. aureus. The minimum inhibitory concentration (MIC) of gentamicin was estimated by broth microdilution method. hla and nuc genes were determined by polymerase chain reaction technique. The biofilm was evaluated using the microtiter plate method in the presence and absence of gentamicin at sub-MIC. The results showed that 18 (31%) and 40 (69%) S. aureus isolates were sensitive and resistant to gentamicin, respectiv

those affected by technological development risks within the scope of medical works. The unprecedented technological development the world witnesses nowadays has been providing brilliant medical service to the human being including examination, diagnosis and the treatment or follow up. However, such works hide behind potential risks threatening people's lives and such risks my be discovered within the limits of now – how and technical knowledge prevailing the time of rendering the medical service. Also this the question is raised on how to keep up between the safety of the patients and such risks are being unknown by the provider and questioning them contradicts the justices. subsequently, can the patients (affected) acquire the compensat

Background: Green Tea is made from the leaf of the plant “Camellia sinensis”. Green tea is reported to contain thousands of bioactive ingredients including catechins which have shown great promise for having antimicrobial effects. Periodontal diseases represent one of the most prevalent diseases around the world and the main etiologic factor behind it, is plaque accumulation, in addition certain kinds of bacteria have been detected frequently in subjects suffering from periodontitis, Several studies suggested that the outcome of periodontal treatment is better if particular pathogens including Aggregatibacteractinomycetemcomitans can no longer be detected after therapy. Materials and Methods: plaque samples were collected from 2

This study aims to model the flank wear prediction equation in metal cutting, depending on the workpiece material properties and almost cutting conditions. A new method of energy transferred solution between the cutting tool and workpiece was introduced through the flow stress of chip formation by using the Johnson-Cook model. To investigate this model, an orthogonal cutting test coupled with finite element analysis was carried out to solve this model and finding a wear coefficient of cutting 6061-T6 aluminum and the given carbide tool.