The experiments were conducted in laboratory conditions of a temperature of 25± 2C and relative moisture of 40± 5 % to evaluate the effectiveness of the cinnamon, lavender and clove essential oils on some biological life aspects of cowpea beetle, C. maculates. Results of the obligative experiment for the effect of the oils on insect adult killing showed that the concentration of 5% caused a mortality percentage averaged 13.33% of the insect males. The mortality percentage of the insect females was 11.3% for the cinnamon and lavender oils. The lavender oil had the lowest effect on adult killing, not exceeding 0. For the effect of the oils on egg laying, clove oil affected the number of eggs highly at the concentration of 5%, resulting in 2.00 eggs on average. The lowest oil effect on egg number was for the lavender oil at the concentration of 1%, leading to an average of 14.73 eggs. The clove oil at the concentration of 5% showed effectiveness in adult emergence prevention as it was not observed that any insect emerged. In contrast, the same oil at the concentration of 1% had less effect, resulting in the highest emergence percentage reaching 13.33%. The same applies to the effect of the plant oils on insect productivity as the clove oil at the concentration of 5% was the most effective; no insect productivity was recorded, unlike the concentration of 1%, recorded productivity of 110.2 %. In the facultative experiment, the highest mortality percentage was recorded using clove oil against females, as the mortality percentage reached 4.00%. In contrast, the lowest mortality percentage was recorded using lavender oil against males, where no killing occurred, as the mortality percentage did not exceed 0.00%. For the effect of the oils on egg laying, the highest affected oil was cinnamon at a concentration of 5% as the number of eggs reached 5.60, while lavender oil at 3% was the least effective; the average number of eggs was 25. Clove oil at a concentration of 5% had the highest effect in reducing the emergence of the insect, so the emergence percentage did not exceed 0.33%. In comparison, its influence was low at 1%, recording the highest emergence percentage (18.67%). The lowest recorded insect productivity average was from the treatment of the clove oil at a concentration of 5%, which did not exceed 5.20%, while the highest productivity average was from the treatment of the lavender oil at 1%, which reached 89.6%. Keywords: essential oils, Cowpea beetle, Callosobruchus maculatus
In this research investigation, a total of eighteen diverse tetra- and penta-lateral cyclic compounds were synthesized. These included 1,3,4-thiadiazole, thiazolidin-4-one (via an alternative method), 1,2,4-triazole, carbothioamide, thiazole-4-one, azetidin-2-one, and oxazole. The synthesis procedure entailed a sequence of reactions. The thiazolidine-4-one 1 was obtained by reaction p-aminobenzoic acid with thiosemicarbazide, followed by treatment with p-tolualdehyde to produce Schiff base 2. Reaction Schiff base 2 with mercaptoacetic acid in dry benzene was carried out to produce thiazolidine-4-one 3. In another synthesis pathway, the esterification of p-nitro benzoic acid with ethanol in the presence of sulfuric acid was
... Show Moreshoulder joint by preparing special exercises for the youth-category wrestling, and through the researchers' follow-up to the wrestling game and their work in the field of rehabilitation and physical therapy, noticing that most of the wrestling players suffer from the shoulder joint pain despite their visit to the specialist doctor and take Treatment, so the researchers saw to study this problem and restore the recovery of the injured through special exercises and a suitable qualification program for the shoulder joint muscles, the goal of research in preparing special exercises and knowing its effect on the rehabilitation of the background muscle of the shoulder for the youth wrestling category. The researchers assumed that there are stati
... Show MoreThe research aims to know the influence of the intellectual capital on the internal control system in a sample of General Inspection Offices in Iraq. The research includes a sample of individuals who are working in these offices total sample (46) individuals distributed according to functional levels (General Inspector, Deputy Inspector General, and Director) , The data and information were collected by using questionnaire, which is done for this purpose, as well as personal interviews in order to reach to the results that achieve the aim of this research , Two hypotheses were formed , the first hypothesis consists of (4) secondary hypothesis , All these hypotheses were tested by using statistical tools such as (percentages, freq
... Show MoreAbstract
The research has discussed the public relations as dependent variable of its branch dimensions( confidence , commitment, control and satisfaction ) and the governmental service quality as independent variable of its branch dimensions (response, dependency, emphasis, tangibility and sympathy), and the research problem has represented by weakness of service quality presented to the customers dealing with company, which is observed via field co-existence of the researcher, where he observe that the quality presented in the company services, are inappropriate with the customers expectations level, also there is weakness of attention and recognition by the
A field study aimed at identifying the sources of mutual complaints among the Directorates of Education staff of their departments and management and run it in their daily dealings with principals in the province of Baghdad, and adopt approach. It was determined the research consists of (2357) male and female employees and 305 randomly stratified simple by the rate of (7%) from the research community as the number of sample reached (167) male and female employees, and selected sample was randomly stratified simple by the rate of (39.67%) of the research community, as the number of sample was (121) principals. It was constructed two questionnaires, the first included (28) items and the second contained (28) items. And the two researchers
... Show MoreThe problem of steady, laminar, natural convective flow in an square enclosure with and without partitions is considered for Rayleigh number (103-106) and Prandtl number (0.7). Vertical walls were maintained isothermal at different temperatures while horizontal walls and the partitions were insulated. The length of partition was taken constant. The number of partitions were placed on horizontal surface in staggered arrangement from (1– 3) and ratio of partition thickness (H/L= 0.033, 0.083, 0.124). The problem is formulated in terms of the vorticity-stream function procedure. A numerical solution based on a program in Fortran 90 with the finite difference method is obtained. Representative results illustrating the effects of the thickn
... Show MoreBackground: Diabetes is a metabolic disorder characterized by chronic hyperglycemia due to an inability to produce insulin. Uncontrolled or poorly controlled diabetes is clinically associated with increased susceptibility to delay healing. Many recent researches have shown that stem cell therapy can be the best choice for treatment of this disease. The aims of this research were investigating regeneration of pancreatic beta cells of diabetic induced rabbits after stem cell transplantation. Materials and Methods: 64 rabbits weighting an average of (2.5 - 3 kg) were used in this experimental study, and divided into 4 groups as follows; group A ( contains 16 healthy rabbits regarded as control group ) , Group B ( contains 16 diabetic rabbits
... Show MoreObjectives: This study aimed to evaluate and compare the effect of plasma treatment versus conventional treatment on the micro shear bond strength (μSBS), surface roughness, and wettability of three different CAD/CAM materials. Materials and methods: Sixty cylindrical specimens (5 mm diameter ×3 mm height) were prepared from three different CAD/CAM materials: Group A: Zirconia, Group B: Lithium disilicate, and Group C: Resin nano-ceramic. Each group was subdivided into two subgroups according to surface treatment used: Subgroup I: Conventional treatment, zirconia was sandblasted with Al2O3, while lithium disilicate and resin nano-ceramic were etched with hydrofluoric acid. Subgroup II: Plasma treatment, the surface of each material was tr
... Show More