Milling process is a common machining operation that is used in the manufacturing of complex surfaces. Machining-induced residual stresses (RS) have a great impact on the performance of machined components and the surface quality in face milling operations with parameter cutting. The properties of engineering material as well as structural components, specifically fatigue life, deformation, impact resistance, corrosion resistance, and brittle fracture, can all be significantly influenced by residual stresses. Accordingly, controlling the distribution of residual stresses is indeed important to protect the piece and avoid failure. Most of the previous works inspected the material properties, tool parameters, or cutting parameters, but few of them provided the distribution of RS in a direct and singular way. This work focuses on studying and optimizing the effect of cutting speed, feed rate, and depth of cut for 6061-T3 aluminum alloy on the RS of the surface. The optimum values of geometry parameters have been found by using the L27 orthogonal array. Analysis and simulation of RS by using an artificial neural network (ANN) were carried out to predict the RS behavior due to changing machining process parameters. Using ANN to predict the behavior of RS due to changing machining process parameters is presented as a promising method. The milling process produces more RS at high cutting speed, roughly intermediate feed rate, and deeper cut, according to the results. The best residual stress obtained from ANN is ‒135.204 N/mm2 at a cutting depth of 5 mm, feed rate of 0.25 mm/rev and cutting speed of 1,000 rpm. ANN can be considered a powerful tool for estimating residual stress
It is commonly known that Euler-Bernoulli’s thin beam theorem is not applicable whenever a nonlinear distribution of strain/stress occurs, such as in deep beams, or the stress distribution is discontinuous. In order to design the members experiencing such distorted stress regions, the Strut-and-Tie Model (STM) could be utilized. In this paper, experimental investigation of STM technique for three identical small-scale deep beams was conducted. The beams were simply supported and loaded statically with a concentrated load at the mid span of the beams. These deep beams had two symmetrical openings near the application point of loading. Both the deep beam, where the stress distribution cannot be assumed linear, and the ex
... Show MoreThis research study experimentally the effect of air flow rate on humidification process
parameters. Experimental data are obtained from air conditioning study unit T110D. Results obtained
from experimental test, calculations and psychometrics software are discussed. The effect of air flow rate
on steam humidification process parameters as a part of air-conditioning processes can be explained
according to obtained results. Results of the steam humidification processes (1,2) with and without
preheating with 5A and 7.5A shows decreasing in dry bulb temperature, humidity ratio, and heat add to
moist air with increasing air flow rate, but humidification load, and total energy of moist air increase with
increasing air flo
When a vehicle is left parked in the sun for an extended period, the gathered heat causes damage to several interiors within the cabin and causes discomfort for people and animals left inside the car. In the present work, the effect of the orientation of a parked white minibus on temperature distribution and cooling load calculation is studied experimentally in an open environment. Two different cases were studied facing south and facing east. For several hours, the temperature inside the car cabin had been monitored and measured at five separate locations. The cooling load calculations are carried out based on the experimental measurements. The results show that the overheating of parked cars always happens as a result
... Show MoreIt is well known that petroleum refineries are considered the largest generator of oily sludge which may cause serious threats to the environment if disposed of without treatment. Throughout the present research, it can be said that a hybrid process including ultrasonic treatment coupled with froth floatation has been shown as a green efficient treatment of oily sludge waste from the bottom of crude oil tanks in Al-Daura refinery and able to get high yield of base oil recovery which is 65% at the optimum operating conditions (treatment time = 30 min, ultrasonic wave amplitude = 60 micron, and (solvent: oily sludge) ratio = 4). Experimental results showed that 83% of the solvent used was recovered meanwhile the main water
... Show MoreFor poets to pay a great attention to the Islamic figures and their symbolism in Islam come as a prominent phenomenon in our literature . As there is an impact of them on the brilliant history commemorated by littérateurs . As a matter of fact ، the chronicle of Imam Ali Ibin Abi Talib (peace be upon him) falls in the orbit of the focus Ibn Abi Al-Hadid Al-Mu'tazili steers to in his poems . The current research study is to trace the portrayal of Imam Ali (peace be upon them) in the poetry of Ibn Abi Al-Hadid Al-Mu'tazili ، Seventh Alwiite Poems ، as there is no a study tacking such a conjecture before. In the article there are two axes : the introduction comes as first axis portraying Imam Ali Ibn Abi Talib (peace be upon him) in the wa
... Show MoreExamining the pictures of the scientific miracles in Surat Al-Ra’d revealed to us - as all other verses of miracles revealed - the truth of the prophecy of our noble Messenger (may God bless him and his family and grant him peace) in receiving the verses of the Qur’an from God Almighty through revelation. It is not possible to talk about cosmic phenomena and their secrets in this way. Fourteen centuries ago, when scientific techniques, observational devices, space surveys, and means of science were non-existent, except for what is related to eye observation, transmitted experiences, and even observation is unable to explain many phenomena near as well as distant ones. The interpretations that are tainted by myth in the books
... Show Moreresearch aims: 1- Demonstrating an aspect of the rhetorical miracle of the Qur’an represented in the accuracy of its verses and the consistency of its topics. 2- Clarifying the intent of Surat Al-Ghashiya, and clarifying the link between the topics of the surah and its purpose. 3- Studying the topics included in Surat Al-Gashiya, and highlighting their consistency among them. 4- Referring to the gifts contained in the noble verses.Research Methodology: In preparing this study, I followed the inductive-analytical approach, according to the procedures outlined in the introduction.From the search results: 1- The purpose of Surat Al-Gashiya: Reminding the Hereafter and its scenes of reward
... Show MoreWisdom in the era before Islam is soo famous and so mature And Wisdom in the age of Islam {the holy quran and AI Hadeeth AI shareef }is dealt with by different meanings that agree with the contexts in which it occurs its contacs One of meanings is wisesaying that occuars in the Halal and Haram .As to the wisdom of the Amawy age ,it was some times absent since it was not dealt with by the great Poets of that age .In the Poetry of AL-FARAZDAK , Wisdom was little and it expressed religious and phsycological meanings because wisdom is amessage that has along –rang .