Traditional tree management is laborious and costly, thus this work aimed to study the performance of two different types of frond cutting saws (reciprocating saw and vibrating saw) and examine the two saws on five date palm varieties. Four parameters were examined, including cutting time for a single frond, the power needed for cutting a single frond, frond cutting productivity expressed as tree/h, and vibration conveyed to the worker’s hand. A field experiment was designed according to the nested randomized complete block design, including five date palm varieties as the main plot and the type of saw as a sub-plot. Means were compared using the least significant differences (LSD 0.05). Results indicated that Bream variety required the least time for frond cutting. The reciprocating saw exhibited efficiency in saving the time required for frond cutting, while the vibrating saw took significantly longer time needed for cutting a single frond. The highest number of fronds cut in one hour was recorded in Bream variety, again significantly higher than the number of other studied varieties. Moreover, the reciprocating saw achieved significantly higher productivity than the vibrating one, indicating that the productivity of the reciprocating saw is almost three times more than the vibrating saw. Maximum productivity was recorded in Bream variety, while the least was recorded in Tebarzal using the vibrating saw. Moreover, results indicate that the variety and the type of saw have a vital role in productivity since as the thickness of a frond increases, the cutting takes more time and ultimately reduces the number of date palms to be pruned per hour. Results also exhibited that vibrating saw reduced the consumed energy during frond cutting. Additionally, results revealed that the minimum power consumed by a vibrating saw was in Bream variety, while Tebarzal consumed the upmost energy when a reciprocating saw was used. Maximum vibration on X-axis was reported in Bream variety when a vibrating saw was used. Additionally, the reciprocating saw exhibited the highest vibration compared with the vibrating saw. Moreover, the reciprocating saw caused the lowest vibration in Tebarzal variety. Results indicated that the vibration imposed by both saws reached the maximum value in Bream variety. The vibrating saw resulted in the higher vibration toward Z axis, while the Reciprocating saw resulted in higher vibration toward X axis, which was more than eight times that recorded by the vibrating saw. Results indicate that vibration toward the Y axis increased significantly in Bream variety compared with others. Again, as in the situation with X and Z axis, the reciprocating saw exhibited the highest vibration compared to that resulted from using a vibrating saw which was more than three times the vibration caused by the vibrating saw.
Objective: To evaluate and compare the effect of mechanical surface treatment (groove, aluminum oxide particles)
with 45 degree bevel type of joint on tensile bond strength of acrylic specimens repaired by two curing methods
(microwave and water both).
Methodology: Eighty specimens (80) were prepared from pink heat cure acrylic resin. They were divided into two
main groups (40 specimen repaired by microwave energy and 40 specimens repaired by water bath method).Each
group can be divided into four subgroups of ten according to the surface treatment. The control group A was left
intact, group B received no surface treatment, group C and D received surface treatment by (groove, 50 m aluminum
oxide particles). Specimens
During the winter, in the industry region (Shaikh Omer) and by applying a passive radon detector (CR-39), lung cancer risk has been measured in twelve rooms of different workshops of two old factories in this site. The radon concentration is ranged from (123.345 Bq/m3) to (328.985 Bq/m3) with an average of (244.19±61.52 Bq/m3). Lung cancer risk ranged from 55.993 to 149.346 per million people and with an average of (110.855 per million people) which were lower than the recommended values (170-230 per million people), so there was no cancer risk on workers in these locations.
NS-2 is a tool to simulate networks and events that occur per packet sequentially based on time and are widely used in the research field. NS-2 comes with NAM (Network Animator) that produces a visual representation it also supports several simulation protocols. The network can be tested end-to-end. This test includes data transmission, delay, jitter, packet-loss ratio and throughput. The Performance Analysis simulates a virtual network and tests for transport layer protocols at the same time with variable data and analyzes simulation results based on the network simulator NS-2.
Abstract
This current research aims to make theoretical frame for the thoughts and principle knowledge for high performance work system ،also trying to know the role that high performance work system practices which is (Effective staffing، comprehensive training، providing work career، and employee participation) play to enhance the organization effectiveness ، although knowing the principles of high performance work system which is: (Shared Information، Knowledge Development Performance and Reward linkage Egalitarianism)and its effect on the organizations. As well as defining the special concept of High performance wo
... Show MoreBeen in this gravel study the effect of Alchgag fast neutrons emitted by the source on the electrical properties of silicon solar cells monounsaturated crystal at a constant rate of neutron flow rate of a wide range of neutron flow speed ranges for periods of time ranging from 2-10 hours
The Adaptive Optics technique has been developed to obtain the correction of atmospheric seeing. The purpose of this study is to use the MATLAB program to investigate the performance of an AO system with the most recent AO simulation tools, Objected-Oriented Matlab Adaptive Optics (OOMAO). This was achieved by studying the variables that impact image quality correction, such as observation wavelength bands, atmospheric parameters, telescope parameters, deformable mirror parameters, wavefront sensor parameters, and noise parameters. The results presented a detailed analysis of the factors that influence the image correction process as well as the impact of the AO components on that process