Traditional tree management is laborious and costly, thus this work aimed to study the performance of two different types of frond cutting saws (reciprocating saw and vibrating saw) and examine the two saws on five date palm varieties. Four parameters were examined, including cutting time for a single frond, the power needed for cutting a single frond, frond cutting productivity expressed as tree/h, and vibration conveyed to the worker’s hand. A field experiment was designed according to the nested randomized complete block design, including five date palm varieties as the main plot and the type of saw as a sub-plot. Means were compared using the least significant differences (LSD 0.05). Results indicated that Bream variety required the least time for frond cutting. The reciprocating saw exhibited efficiency in saving the time required for frond cutting, while the vibrating saw took significantly longer time needed for cutting a single frond. The highest number of fronds cut in one hour was recorded in Bream variety, again significantly higher than the number of other studied varieties. Moreover, the reciprocating saw achieved significantly higher productivity than the vibrating one, indicating that the productivity of the reciprocating saw is almost three times more than the vibrating saw. Maximum productivity was recorded in Bream variety, while the least was recorded in Tebarzal using the vibrating saw. Moreover, results indicate that the variety and the type of saw have a vital role in productivity since as the thickness of a frond increases, the cutting takes more time and ultimately reduces the number of date palms to be pruned per hour. Results also exhibited that vibrating saw reduced the consumed energy during frond cutting. Additionally, results revealed that the minimum power consumed by a vibrating saw was in Bream variety, while Tebarzal consumed the upmost energy when a reciprocating saw was used. Maximum vibration on X-axis was reported in Bream variety when a vibrating saw was used. Additionally, the reciprocating saw exhibited the highest vibration compared with the vibrating saw. Moreover, the reciprocating saw caused the lowest vibration in Tebarzal variety. Results indicated that the vibration imposed by both saws reached the maximum value in Bream variety. The vibrating saw resulted in the higher vibration toward Z axis, while the Reciprocating saw resulted in higher vibration toward X axis, which was more than eight times that recorded by the vibrating saw. Results indicate that vibration toward the Y axis increased significantly in Bream variety compared with others. Again, as in the situation with X and Z axis, the reciprocating saw exhibited the highest vibration compared to that resulted from using a vibrating saw which was more than three times the vibration caused by the vibrating saw.
Objective: Patient satisfaction is critical to ensure patient adherence during orthodontic treatment. This study aimed to evaluate patient satisfaction with orthodontic care and related services provided for Iraqi sample at the College of Dentistry, University of Baghdad. Materials and Methods: A questionnaire-based prospective study was conducted to assess patient satisfaction by using a three-point response rating. The questionnaire contained seven sections divided into 21 questions that covered overall patient relationship with the orthodontic staff, proposed treatment explanation, and orthodontic treatment quality. The questionnaire standard was set so that at least 90% “always” response should be shown by all
... Show More
Sumatriptan(ST) is a selective agonist at serotonin 5-HTI receptors, as well as 5-HT1B/1D subtypes. It is effective for acute migraine attacks, but has a short half life (about 2 hours) and low oral bioavailability (15%). The purpose of this study was to develop and optimize nasal mucoadhesive in-situ gel(IG) of ST to enhance nasal residence time for migraine management. Cold method was used to prepare different formulas of ST nasal IG, using thermosensitive polymers (poloxamer 407 alone or with poloxamer 188) with a mucoadhesive polymer hyaluronic acid (HA) which were examined for gelation temperature and gelation time, pH, drug content, gel strength, spreadability, muc
... Show More
The main aim of this study is to evaluate the remaining oil in previously produced zones, locate the water productive zone and look for any bypassed oil behind casing in not previously perforated intervals. Initial water saturation was calculated from digitized open hole logs using a cut-off value of 10% for irreducible water saturation. The integrated analysis of the thermal capture cross section, Sigma and Carbon/oxygen ratio was conducted and summarized under well shut-in and flowing conditions. The logging pass zone run through sandstone Zubair formation at north Rumaila oil field. The zones where both the Sigma and the C/O analysis show high remaining oil saturation simila
... Show MoreNasiriya field is located about 38 Km to the north – west of Nasiriya city. Yammama, a giant lower cretaceous reservoir in Nasiriya field which is lithologically formed from limestone. Yammama mainly was divided into three main reservoir units YA, YB1, YB2 and YB3 and it is separated by impermeable layers of variable thickness. An accurate petro physical evolution of the reservoir is of great importance perform an excellent geological model so that four petro physical properties which are shale volume, porosity, water saturation and permeability was re-evaluated. The volume of shale was calculated using the density and neutron logs (VSH-DN) rather than using gamma ray log because of presence a uranium content in the formation that make
... Show MoreThis study aims to encapsulate atenolol within floating alginate-ethylcellulose beads as an oral controlled-release delivery system using aqueous colloidal polymer dispersion (ACPD) method.To optimize drug entrapment efficiency and dissolution behavior of the prepared beads, different parameters of drug: polymer ratio, polymer mixture ratio, and gelling agent concentration were involved.The prepared beads were investigated with respect to their buoyancy, encapsulation efficiency, and dissolution behavior in the media: 0.1 N HCl (pH 1.2), acetate buffer (pH 4.6) and phosphate buffer (pH 6.8). The release kinetics and mechanism of the drug from the prepared beads was investigated.All prepared atenolol beads remained f
... Show MoreEvaluation of Dot. ELISA test for Diagnosis Visceral Leishmaniasis in Infected Children