Surficial sediment samples were collected from four stations at Shatt Al-Hilla from Western Zoer area to Almaimirh in Babylon province for the period from August 2016 to April 2017.The level of contamination in the sediments of Shatt Al-Hilla, by Lead (Pb), Copper (Cu), Nickle (Ni), Manganese (Mn), Zinc (Zn), Arsenic (As), and Cobalt (Co) has been evaluated using the index of Geo-accumulation (I-Geo), Contamination factor (CF), pollution load index (PLI) and Potential ecological risk index (Eire). In the present study the levels of heavy metals in sediment samples were found in the range of (10-15.22 ppm) for Pb, (25.6-46.09 ppm) for Cu,(144.9-413.7 ppm) for Ni, (666.1- 906.3 ppm) for Mn, (68.69- 119.2 ppm) for Zn, for As (5.22- 8.25 ppm

Nanostructural cupric oxide (CuO) films were prepared on Si and glass substrate by pulsed laser deposition technique (PLD) using laser Nd:YAG, using different laser pulses energies from 200 to 600 mJ. The X-ray diffraction pattern (XRD) of the films showed a polycrystalline structure with a monoclinic symmetry and preferred orientation toward (111) plane with nano structure. The crystallite size was increasing with increasing of laser pulse energy. Optical properties was characterized by using UV–vis spectrometer in the wave lengthrange (200-1100) nm at room temperature. The results showed that the transmission spectrum decreases with the laser pulses energy increase. Sensitivity of NO2 gas at different operating temperatures, (50°C,

In this study, the stresses and displacement around a tunnel opening under water body in Baghdad city, middle of Iraq, during excavation and lining are discussed. For this purpose, the finite element method (FEM) was adopted as an effective approach to analyze the problem using (SIGMA/W) program. The research includes the study of the behavior of soil due to excavation of a tunnel by calculating the displacements and stresses in three positions of the tunnel (crown, wall, and invert) during the various stages of construction. The surface settlement is also studied. The finite element analyses were carried out Using (Elastic- plastic) and (linear elastic) models for the soil and the concrete liner respectively.

While traditional energy sources such as oil, coal, and natural gas drive economic growth, they also seriously affect people’s health and the environment. Renewable energies (RE) are presently seen as an efficient choice for attaining long-term sustainability in development. They provide an adequate response to climate change and supply sufficient electricity. The current situation in Iraq results from a decades-long scarcity of reliable electricity, which has impacted various industries, including agriculture. There are diverse prospects for using renewable energy sources to address the present power crisis. The economic and environmental impacts of renewable energy systems were investigated in this study by using the solar pumpi

Abstract

The research discusses the biography of Imam Al-Qanuji,  his syllabus in his book “ Raudha Al- Nadia , and Public, particular, edition  definition. Then it mentions the types of matters and the Imam Al-Qanuji’s opinion in it, and it mentions the early and contemporary scholars’ opinions and simplifies their logical and unwritten proofs. It also discusses and librates the place of dispute, then it swages reliable based on the power of the proof and interest without any contravention which the orthodox law orders.  Furthermore, the research discusses matters like,  whether there is any particular formula for public, or whether the public considers the Quraan as i

The microstructure and wear properties of 392 Al alloy with different Mg contents were studied using centrifugal casting. All melted alloys were heated to 800 ºC and poured into the preheated centrifugal casting mold (200-250 ^ºC) at different mould rotational speeds (1500, 1900 and 2300 r.p.m).  It is clear from the results obtained that wear rate was dependent on the Mg content, applied load and mould rotational speed. Furthermore, wear test showed that the minimum wear rate was found in the inner layer of produced rings at mould rotational speed of 1900 r.p.m and Mg content of 5%.