The pure and Sb doped GeSe thin films have been prepared by thermal flash evaporation technique. Both the structural and optical measurement were carried out for as deposited and annealed films at different annealing temperatures.XRD spectra revealed that the all films have one significant broad amorphous peak except for pure GeSe thin film which annealed at 573 K, it has sharp peak belong to orthorhombic structure nearly at 2θ=33o. The results of the optical studies showed that the optical transition is direct and indirect allowed. The energy gap in general increased with increasing annealing temperature and decreased with increase the ratio of Sb dopant. The optical parameters such as refractive index, extinction coefficient and real and

This research aims to study the effect of microwave furnace heat on the mechanical properties and fatigue life of aluminum alloy (AA 2024-T3). Four conditions were used inside microwave furnace (specimens subjected to heat as dry for 30 and 60min. and specimens subjected to heat as wet (water) for 30 and 60 min.), and compared all results with original alloy (AA 2024-T3). Tensile, fatigue, hardness and surface roughness tests were used in this investigation. It is found that hardness of dry conditions is higher than wet conditions and it increases with increasing of time duration inside microwave furnace for dry and wet conditions. Also, tensile strength has the same behavior of hardness, but it increases with decreasing

The aim of the present research is concerned with study the effect of UV radiation on the optical properties at wavelengths 254, 365 nm of pure PC and anthracene doping PC films prepared using the cast method for different doping ratio 10-60 mL. Films of pure PC and anthracene doping PC were aged under UV radiation for periods of up to 360 h. It found that the effect of UV radiation at wavelength 254 nm on the optical properties is great than the effect of UV radiation at wavelength 365 nm. Also, it found that the optical energy gap of pure PC and anthracene doping PC films is stable against radiation.

Dental implants can be made of various materials, and amongst them, titanium and titanium alloy were the materials of choice for dental implants for many years because of their biocompatibility. The two alloys have a high level of biocompatibility, a lower modulus of elasticity, and better corrosion resistance than other alloys. Thus, they are frequently utilized in biomedical applications and mostly replace stiff fabrics. The latest advances in a new strontium oxide–cp titanium composite alloy are the main topic of this research. With regard to biomedical applications, additions of strontium oxide were synthesized at three distinct weight percentages (2%, 4%, and 6% by wt%). Powder metallurgy was used to create the alloys, which

The nonlinear optical properties response of nematic liquid crystal (6CHBT) and the impact of doping with two kinds of nanoparticles; Fe₃O₄ magnetic nanoparticles and SbSI ferroelectric nanoparticles have been studied using the non-linear dynamic method through z-scan measurement technique. This was achieved utilizing CW He-Ne laser. The pure LC and magnetic LC nanoparticle composite samples had a maximum absorption while the ferroelectric LC nanoparticle composite had a minimum absorption of the incident light. The nonlinear refractive index was positive for the pure LC and the rod-like ferronematic LC composite samples, while it was negative for the ferroelectric LC composite. The studying of the nonlinear optical

Vitrifications process one of the important methods to immobilize nuclear waste.  In this research nuclear waste (Strontium Oxides) with molecular weight (5%) was immobilized by vitrification methods in two types of borosilicate glass (c-type) which are glass and glass-ceramics. To investigate the physical, chemical and mechanical properties of glass and glass-ceramic after immobilize nuclear waste these samples irradiated by gamma ray radiation. Co-60 was used as gamma a irradiation with dose rate 0.38 kGy/hr for different period of time. It’s found that gamma radiation affected the glass and glass-ceramic properties. From phase analysis by the x-ray diffraction for glass-ceramic samples proved that at doses 343kGy change the cry

Abstract:
This research aims to the importance of oil in achieving economic
security in the Arab. Oil is not an ordinary subject and returns it significance to
the followings:
1. The importance of skipping a source of energy.
2. The importance of oil as raw material for petrochemical industry.
3. The importance of the oil sector as an area of foreign investment
4. The importance of oil in the marketing activities, transport, insurance
and various services
In addition to the importance of oil in general and the Arab oil has
additional strategic advantages such as geographic location, And the
magnitude of reserves and production of heavy investment costs are relatively
simple, And the ability to meet the

In the name of of Allah the Merciful
        Praise be to God, and blessings and peace be upon the Messenger of God, Muhammad, and upon his family and his family and peace, and after:
 The honor of every knowledge of honor is related to it, and since the science of interpretation is related to the Book of God Almighty; it is considered one of the most noble and longest of sciences, and this science began long ago as the early ages of Islam have expanded the Islamic state, and people entered the religion of God in cohorts, and the mixture mixed In tongues, and people did not know much about the meanings of the Qur’an, so the need for authorship in this great knowledge was severe, and pe

The history of the arts is closely connected with the history of humankind, since it is impossible to separate our scientific and artistic advances’. Therefore, the current research focuses on the close bond between art and other disciplines. The connection of the arts to the sciences is unequivocal and undisputed; the contributions of artists to the various scientific domains are clear. If one scrutinises the ability of artists to participate in building societies, one will find that the arts have penetrated deeply into a range of products and inventions, starting with the pencil and ending with the missile. The artist’s contributions play a part in the minutest of details across all fields of industry: production, craftsmanship, me