Tooth restoration one of the most common procedures in dental practice. The replacement of the entire restoration leads to loss of tooth structure and increase risk of pulp injury; replacement is also time consuming and costly. According to the minimally invasive approach when minimal defects, repair is the better choice than the total replacement of the restoration. This study aims to evaluate repair rating versus replacement treatment procedure for defective composite fillings among Iraqi dentists. Material and methodology: A questionnaire survey were designed and distributed to 184 post-graduate dentists in Iraq. The inquiry pertained general information; including their clinical experience in years, their preference in terms of direct c

This study investigated the structural behavior of a beam–slab member fabricated using a steel C-Purlins beam carrying a profile steel sheet slab covered by a dry board sheet filled with recycled aggregate concrete, called a CBPDS member. This concept was developed to reduce the cost and self-weight of the composite beam–slab system; it replaces the hot-rolled steel I-beam with a steel C-Purlins section, which is easier to fabricate and weighs less. For this purpose, six full-scale CBPDS specimens were tested under four-point static bending. This study investigated the effect of using double C-Purlins beams face-to-face as connected or separated sections and the effect of using concrete material that contains different recycled

In this paper, numerical and experimental studies on the elastic behavior of glass fiber reinforced ‎polymer (GFRP) with stiffeners in the GFRP section's web (to prevent local buckling) are presented. ‎The GFRP profiles‎ were connected to the concrete deck slab by shear connectors. Two full-scale simply supported ‎composite beams (with and without stiffeners) were tested under impact load (three-point load) to ‎assess its structural response. The results ‎proved that the maximum impact force, maximum ‎deflection, damping time, and ‎damping ratio of the composite beam were affected by the GFRP ‎stiffeners‎. The experimental results indicated that the damping ratio and deflection were diminished compare

The aim of this research is to investigation the optimization of the machining parameters (spindle speed, feed rate, depth of cut, diameter of cutter and number of flutes of cutter) of surface roughness for free-form surface of composite material (Aluminum 6061 reinforced boron carbide) by using HSS uncoated flat end mill cutters which are rare use of the free-form surface. Side milling (profile) is the method used in this study by CNC vertical milling machine. The purpose of using ANFIS to obtain the better prediction of surface roughness values and decreased of the error prediction value and get optimum machining parameters by using Taguchi method for the best surface roughness at spindle speed 4500 r.p.m, 920mm/rev feed rate, 0.6mm de

Aim This study is an overview of NPEV investigated during AFP surveillance programs for the period 2010–2017 in Iraq. Methods Stool samples from 4296 AFP cases and 2933 healthy contacts among children less than 15 years of age were processed for virus isolation as a part of AFP surveillance for the Global Polio Eradication Program in Iraq at National Polio Laboratory. NPEV detection was performed by virus isolation on cell culture according to WHO recommendations. Results The NPEV isolation rate was 14% of total AFP cases and 14.5% of healthy contacts. The infection rate was higher in males than females with a male/female ratio of 1.5: 1. The highest NPEV infection rate was observed among the children aged 1-2 years and decrease significa

Background: In the present study used device jet plasma needle with atmospheric pressure which  generates non thermal plasma jet to measure treatment potent with plasma against pathogenic bacteria  founded  in UTI  was inactivated with plasma at 10 sec,

Objective:. This work included the application of the plasma produced from the system in the field of bacterial sterilization , where sample of Gram- negative bacteria (Escherichia coli) were exposed to intervals (1-10)second . Midstream Urine samples swabs were obtained from patients with urinary tract infections.

Type of the study: Cross -sectional study.

Methods: The work were used i

Mental systems in ontological discourse turned into deliberative systems, derived from the non-coordinated thought that motivated ontological discourse, as an incomplete thought, after it became close to reason; Between creation and prevention, between reasoning and creation, between submission and ambition, the result of an interconnected entity that slays one another from one another, and intersects with one another, to produce a special pattern each time, completely different from its predecessor or to provide a path for the coordination of others, which is outside the linguistic event, or part From it, signs and marks, produced to a large extent M., and united the signs; to return again in a circular and rotational movement to produc

The use of antibiotics without prescription (self-medication) is growing globally and is associated with increased bacterial resistance, ineffective treatment and adverse reactions. This study aimed at assessing the practice of antibiotic self-medication in the Iraqi population. A cross-sectional study design was adopted in this work. The sample was comprised of 303 staff members from the non-medical colleges in Iraq. An online questionnaire was distributed between the 29^th of June to the 14^th of September 2021 to collect data including socio-demographic characteristics and questions about antibiotic self-medication. Most of the participants had a university degree and a moderate monthly income. The majority (88%) h

Companies seek to enhance investor confidence by achieving the highest level of transparency in disclosure of financial and non-financial information (SASB standards) for Iraqi insurance companies listed on the financial market. The aim of the research is to identify the extent of the ability of financial and non-financial information to enhance transparency in reporting, which is reflected in Investor confidence. And the standards of sustainability development accounting issued by (SASB) through the electronic questionnaire that was distributed. Companies seek to achieve a set of goals, the most important of which is to enhance investor confidence by improving transparency in disclosure. Concerning the employment of financial an