The Khabour reservoir, Ordovician, Lower Paleozoic, Akkas gas field which is considered one of the main sandstone reservoirs in the west of Iraq. Researchers face difficulties in recognizing sandstone reservoirs since they are virtually always tight and heterogeneous. This paper is associated with the geological modeling of a gas-bearing reservoir that containing condensate appears while production when bottom hole pressure declines below the dew point. By defining the lithology and evaluating the petrophysical parameters of this complicated reservoir, a geological model for the reservoir is being built by using CMG BUILDER software (GEM tool) to create a static model. The petrophysical properties of a reservoir were computed using the notion of hydraulic units, and there are a number of basic steps to building a geological model, beginning with the creation of a single well model and then moving on to the distribution of properties. Depending on the variance in petrophysical parameters, the reservoirs were separated into seven zones. The Ordovician Formation (Khabour Formation) is penetrated by well Akk-1, which is included in the single well geological model to focus on studying the impact of gas condensate on gas production. The prediction of gas condensate wells production will strongly depend on oil banking evaluation and modeling. For this reason, well Akk-1 was chosen to build the model. Upper and lower sandstone units characterized as the most important due to containing of gas. The cost and risk to develop these reservoirs under severe conditions of pressure and temperature highlight the need to be able to confidently predict the recovery of gas and liquid drop-outs from Khabour reservoirs so, it is so necessary to predict the cost of this step in another paper
In this study, the effect of construction joints on the performance of reinforced concrete beams was experimentally investigated. Seven beam specimens, with dimensions of 200×100×1000 mm, were fabricated. The variables were considered including; the location and configuration of the joints. One beam was cast without a joint (Reference specimen), two specimens were fabricated with a one horizontal joint located either at tension, or compression zone. The fourth
beam had two horizontal joints placed at tension, and compression area. The remaining specimens were with one or two inclined joints positioned at the shear span or beam’s mid-span. The specimens were subjected to a monotonic central concentrated loading until the failure. T
This paper deals with prediction the effect of soil remoulding (smear) on the ultimate bearing capacity of driven piles. The proposed method based on detecting the decrease in ultimate bearing capacity of the pile shaft (excluding the share of pile tip) after sliding downward. This was done via conducting an experimental study on three installed R.C piles in a sandy clayey silt soil. The piles were installed so that a gap space is left between its tip and the base of borehole. The piles were tested for ultimate bearing capacity
according to ASTM D1143 in three stages. Between each two stages the pile was jacked inside the borehole until a sliding of about 200mm is achieved to simulate the soil remoulding due to actual pile driving. T
Water pollution is one of the global challenges that the society must address in the 21st century aiming to improve the water quality, reduce human pollutants and ecosystem health impacts. In phytotoxicity test, the plant of Iresine herbstii was exposed to remove nickel from simulated wastewater using two different ratios (mass of plant to the mass of nickel) (,Rp/Ni) for 21 days with sub-surface batch system. During the exposure period, the removal of Ni concentrations (2, 5 and 10 mg/L) for two mass ratio (2,800 and 34,000) were (83.6%, 77.2%, 78.0%) and (86.8%, 97% and 95.6%), respectively. final result of the rate was found that the highest removal occurred, 97%, at a mass ratio of 34,000 and
... Show MoreThe present work aimed to study the SiO2μPs, and NPs effect on the biodegradability of St/PVA blends. The samples were prepared by casting method as PVA, St/PVA blends with different concentrations (30, 40, 50, and 60 %). FTIR test was carried out for the samples preparation. The results proved some changes which might be related to changing in crystallinity of St/PVA matrix as well as physical incorporation of SiO2 μPs, and NPs addition. The enzymatic test and water uptake results proved that increase in weight loss with increases of starch ratio. The lowest weight loss was PVA; the highest weight loss is 60% St/PVA whereas the lowest weight loss is 30%St/PVA for blends involved. SiO2μPs (753.7 nm), and NPs (263.1 nm) were added at d
... Show MoreThis qualitative study was conducted on eight types of commercial baking yeast which available in local markets to estimate their fermentation activity as affecting the Bread industry and the impact of the salt added to DoughLeavening, The results showed a great variation in the fermentation capacity of yeast samples (their role in swelling the dough), most notably the sample value Y3 and least sample Y7 and reached 80% and 20% respectively, and the value of Leavening by using the two types of yeast with addition of three levels of salt (0 , 1 and 2%) have 20.0 , 19.7 and 15.7 of the sample Y3, compared with 10.5 , 10.3 and 8.8 of the sample Y7 for each of the levels of salt respectively, reflect
... Show MoreCitrus fruits are one of the consumer agricultural products of the Iraqi citizen. It is rich in vitamins and usedin many food industries as well as medicines. Classifying the amount of production of citrus treesaccording to the producing governorates has been done to find a map that shows the production of citrustrees according to Iraqi governorates. A cluster analysis method was used according to the hierarchicalmethod. The results showed that Najaf and Qadisiyah are the most similar in citrus production, whileSaladin and Najaf were the two governorates with the furthest distance in proximity matrix. Diyalagovernorate was clustered in the first cluster within two, three, four or five of the clusters for classifyingIraqi governorates covere
... Show MorePollen grains morphology have been studied for the wild species of the genus Erysimum L. which belong to Crucifereae family in Iraq. These species are E. filifolium Boiss. et Hausskn., E. oleifolium J. Gay, E. repandum L., E. eginense Hausskn. ex Bornm., E. aucheranum J. Gay, E. cheiranthoides L., E. alpestre Ky. ex Boiss., E. kurdicum Boiss. et Hausskn., E. tenellum DC., E. strophades Boiss., E. gladiiferum Boiss. et Hausskn., E. nasturtioides Boiss. et Hausskn. The study was performe by using light microscope . The study reveal that there was only one type of pollen grain named Tricoplate in all studied species . The study also demonstrated that there were differences among pollen grains morphology . The species E. kurdicum , E. alpestre
... Show MoreIn this research, the X-ray diffraction pattern was used, which was obtained experimentally after preparation of barium oxide powder. A program was used to analyze the X-ray diffraction lines of barium oxide nanoparticles, and then the particle size was calculated by using the Williamson-Hall method, where it was found that the value of the particle size is 25.356 nm. Also, the dislocation density was calculated, which is equal to1.555 x1015 (lines/nm2), and the value of the unit cell number was also calculated, as it is equal to 23831.