Thermomechanical analysis (TMA) and differential scanning calorimetry (DSC) are used to investigate the effect of molding and annealing of polyester on the behavior of thermal expansion and crystallization since these factors play role in the reprocessing or recycling of the polymer. The dynamic mode of the TMA provides enhanced characterization information about the polyester since it separates the transitions into reversible and irreversible signals, and also reveals the progress of the amorphous regions as the polyester loses strength with the increasing temperature approaching melting. Slow cooling after annealing brings crystallization that may be attributed to molecular chain straightening due to orientation.
When a vehicle is left parked in the sun for an extended period, the gathered heat causes damage to several interiors within the cabin and causes discomfort for people and animals left inside the car. In the present work, the effect of the orientation of a parked white minibus on temperature distribution and cooling load calculation is studied experimentally in an open environment. Two different cases were studied facing south and facing east. For several hours, the temperature inside the car cabin had been monitored and measured at five separate locations. The cooling load calculations are carried out based on the experimental measurements. The results show that the overheating of parked cars always happens as a result
... Show MoreIn addition to the primary treatment, biological treatment is used to reduce inorganic and organic components in the wastewater. The separation of biomass from treated wastewater is usually important to meet the effluent disposal requirements, so the MBBR system has been one of the most important modern technologies that use plastic tankers to transport biomass with wastewater, which works in pure biofilm, at low concentrations of suspended solids. However, biological treatment has been developed using the active sludge mixing process with MBBR. Turbo4bio was established as a sustainable and cost-effective solution for wastewater treatment plants in the early 1990s and ran on minimal sludge, and is easy to maintain. This
... Show MoreENGLISH
The Rwandan author of comfort chests and verse pleasure of the most important historians of the Seljuks in the sixth century AH / twelfth century and belongs to the mostly ethnic scientists family has won favor with the Sultans of the Seljuks until he became the most famous Markhém is his main source of research sources with respect to the political and social history the Seljuks and the relationship of the Seljuk sultans of the Abbasid caliphs in Baghdad.
The book included the history of the Seljuks from the time of statehood in the fifth century AH / atheist century AD until the death of the Sultan Tgrl bin Arslan year 590 AH / 1193 AD and then shed Akhawarzmeyen, and touched the author at the end of the book in separate chapters t
The importance of the research comes from dealing with the problem of lack of traffic awareness, which causes accidents and the occurrence of human and material losses, and the research aims to study the role of satellite channels in forming traffic awareness among the public, and a sample was chosen from Baghdad consisting of (280) individuals, male and female, and used the questionnaire tool. To obtain the data, which included several questions, the results were analyzed statistically and several results were reached, the most important of which is that there is an interest among the public in following traffic programs at a rate of one to two hours to receive information through traffic programs and to identify and apply gener
... Show MoreBackground The application of nanotechnology to biomedical surfaces is explained by the ability of cells to interact with nanometric features. The aim of this study was to consider the role of nanoscale topographic modification of CPTi dental implant using chemical etching method for the purpose of improving osseointegration. Materials and methods: Commercial pure titanium rod was machined into 20 dental implants. Each implant was machined in diameter about 3mm, length of 8mm (5mm was threaded part and 3mm was flat part). Implants were prepared and divided into 2 groups according to the types of surface modification method used: 1st group (10 implant) remained without nano surface modification (control), 2nd group include (10 implant) etche
... Show MoreThe experiment was conducted to evaluate and performance comparison for moldboard and disk plows in central of Iraq in 2011. Three factor were used in this study included Two types of plows included moldboard and disk plows which represented main plot , three forward speeds of the tillage was second factor included 1.85, 3.75 and 5.62 km / h which represented sup plot , and three levels of soil moisture was third factor included 21 , 18 and 14 % to determined data actual plow depth , Practical productivity, Volume of disturbed soil, Field efficiency , Slippage percentage in silt clay loam soil with depth 22 cm were studied in the experiment Split – split plot design under randomized complete block design with three replications using
... Show MoreTill now, isatin derivatives have received a lot of interest in organic and medicinal chemistry due to their significant biological and pharmacological activities. Schiff’s and Mannich bases of isatins are an effective group of heterocyclic derivatives that play a significant role in medicinal chemistry as antimicrobial agents. In light of these facts, new Schiff bases and Mannich bases of isatin were synthesized. The monomer Mannich bases; 3(a-e) have been synthesized by reacting isatin with different secondary amines, piperidine, morpholine, and pyrrolidine, dimethylamine, diphenylamine, separately, and formaldehyde, while the dimer (5) formed by using piperazine and formaldehyde which then react separately with Phenylhydrazine
... Show MoreShatt Al-Diwaniya branches from Shatt Al-Hilla and extends for about 112 km until the Al-Rumaitha district within the study area located in Al-Diwaniya Governorate, Iraq. It is considered the main source for providing drinking water and supplying irrigation projects to the cities Al-Diwaniya and Al-Rumaitha. The study aims to evaluate, study, and develop Shatt Al-Diwaniya, as well as the new lined canal branching from Shatt Al-Diwaniya which. It is called Shatt Al-Diwaniya Diversion Canal. Field measurements of the discharge and water level were monitored, six sets for Shatt Al-Diwaniya and three sets for Diversion Canal. A one-dimensional model was developed by using HEC-RAS 5.0.7 so