This paper presents the Taguchi approach for optimization of hardness for  shape memory alloy (Cu-Al-Ni) . The influence of  powder metallurgy parameters on hardness has been investigated. Taguchi technique and ANOVA were used for analysis. Nine experimental runs based on Taguchi’s L9 orthogonal array were performed (OA),for two parameters was study (Pressure and sintering temperature) for three different levels (300 ,500 and 700) MPa ,(700 ,800 and  900)^oC respectively . Main effect, signal-to-noise (S/N) ratio was study, and analysis of variance (ANOVA) using  to investigate the micro-hardness characteristics of the shape memory alloy .after application the result of study shown the hei

A high Tc superconductor with a nominal composition
(Bi1-xPbx)2(Sr1-yBay)2Ca2Cu3O10+δ for (0 £ x £ 0.5) and (0 £ y £ 0.5) was prepared by
a solid state reaction method. The effect of the substitution of Pb for Bi and Ba for Sr and
quenching temperature on the superconductivity has been investigated to obtain the
optimum conditions for the formation and stabilization of the high Tc phase (2223).
The results showed that the optimum sintering temperature for the pure composition is
equal to 875°C and the sintering time is equal to 240h with heating and cooling rate of
60°C/h . Our results indicated that a small amount of (Ba = 0.1) could raise the transition
temperature (Tc), but enhancing Ba to 0.4 has raised

Changes in mechanical properties of material as a result of service in different conditions can be provided by mechanical testing to assist the estimation of current internal situation of these materials, or the degree of deterioration may exist in furnaces serviced at high temperature and exceed their design life. Because of the rarity works on austenitic stainless steel material type AISI 321H, in this work, ultimate tensile strength, yield strength, elongation, hardness, and absorbed energy by impact are evaluated based on experimental data obtained from mechanical testing. Samples of tubes are extracted from furnace belong to hydrotreaterunit, also samples from un-used tube material are used to make comparisons between these properti

The present research aims to study the effect of friction stir welding (FSW) parameters on temperature distribution and tensile strength of aluminum 6061-T6. Rotational and traverse speeds used were (500,1000,1400 rpm) and (14,40,112 mm/min) respectively. Results of mechanical tests showed that using 500rpm and 14mm/min speed give the best strength. A three- dimensional fully coupled thermal-stress finite element model via ANSYS software has been developed. The Rate dependent Johnson-Cook relation was utilized for elasto-plastic work deformations. Heat-transfer is formulated using a moving heat source, and later used the transient temperature outputs from the thermal analysis to determine equivalent stresses in the welde

The present study reports Morchella conica Pers.1818, which belongs to the family, Morchellaceae as a new record of Iraqi macromycota based on the morphological and molecular methods. During their short and often sporadic fruiting season, this fungal species was found in mixed forest unburned areas in Branan ranges (Suliamaniya Province, Northeast Iraq). Currently, M. conica is the second Morchella species reported from Iraq. The current study aimed to introduce this new record, which is poorly studied in the Middle East. M. conica is morphologically described and phylogenetically confirmed. The relationship between this species and other species within the genus was studied using the nrDNA ITS sequences from different species and divers

The Old World Screwworm Fly Chrysomya bezziana is a new insect pest on cattles and other domestic recor¬ded for the first from Iraq. It was first observed in cow's vagina in September of 1996 in Shaikh Hammed (Tarmiya), near Baghdad city. Chrysomya bezziana Villeneuve is well known as one of the most important insect pests of livestock. Its larvae infest living tissues by causing myiasis. In a wide range of worm-blooded host species (Spradbery and Vanningham, 1980; Spradbery and Kirk. 1992). It is widely dist¬ributed species over an extensive area of tropical and subtropical Africa, the Arabian Gulf countries, Iran. Indian subcontinent. South-East Asia. Indonesia, and as far east as Papua New Guinea (Zurapt, 1965; Djalayer et al. 1978;

Phenomena of an abnormal genitalia was among some specimens of Cicindela aulica Dej.
Collected from Iraq. The fore tarsi of male were asymmetrical having its basal three segments
dilated and clothed beneath with fine bristles as in normal male. While those of the right leg
were found simple as in normal females. Dissection of the genialia of these specimens
showed that they were of two types of both male and female structures.

This study is the first investigation in Iraq dealing with genotyping of IL-4 −590 (C>T) gene, especially in Iraqi patients with asthma. We studied forty-eight blood samples collected from patients with asthma and compared with age-matched 25 healthy individuals as controls. The polymorphism results of IL-4 −590 (C>T) gene by using amplification refractory mutation system (ARMS-PCR) showed the presence of C and T alleles and three genotypes (CC, CT, and TT). Interestingly the frequency of C allele and CC genotype was higher in patients with asthma in comparison with the same allele and geno