This study investigates the characterization and mechanical performance of Stone Mastic Asphalt (SMA) mixtures modified with two types of polymers: styrene–butadiene–styrene (SBS) and high-molecular-weight polyethylene (PE). Neat asphalt cement PG 64-16 was modified using a higher content of SBS and PE at concentrations of 6%, 7%, and 8% by weight of asphalt through the dry blending method to produce Highly Modified Asphalts (HiMA). The physical and rheological properties of the modified binders were evaluated using penetration, softening point, rotational viscosity, and dynamic shear rheometer (DSR) tests. Also, their phase compatibility and morphological changes were evaluated using the storage stability testing and scanning electron microscopy (SEM) analysis. The mechanical performance of the corresponding SMA mixtures was assessed through Marshall stability and flow, moisture susceptibility, crack tolerance index (CT-index), resilient modulus, and rutting resistance tests. Also, a mechanistic durability analysis was conducted using the KENLAYER software. Results indicated that both polymers enhanced the binder’s stiffness and high-temperature performance, with SBS exhibiting greater overall improvements. SBS-modified binders displayed a relatively low softening point difference (ΔT) of 5.1 °C to 5.8 °C, indicating good thermal stability and uniform polymer dispersion. In contrast, PE-modified binders exhibited significantly higher ΔT values, reaching 13.5 °C with 8% PE content, indicating a greater tendency toward phase separation. Moreover, Marshall stability improved substantially, increasing by 43% for 8% SBS-modified mixes and 28% for 8% PE-modified mixes compared to the neat SMA mix. Flow number (FN) results indicated enhanced rutting resistance, with FN values increasing by 2.45 times for SBS mixes and 2.1 times for PE mixes at 8% polymer content. Additionally, moisture susceptibility was significantly improved, as evidenced by the tensile strength ratio (TSR) values of 97% with 8% SBS and 92% with 8% PE, compared to 81% for the neat mix. Resilient modules increased notably, with a 38% rise for 8% SBS mixes and a 24% rise for 8% PE mixes, reflecting enhanced stiffness and load-bearing capacity. Also, the CT-index significantly improved, reaching values of 154 for the 8% SBS mix and 127 for the 8% PE-modified mix, compared to 86 for the neat mix, indicating enhanced resistance to cracking. Finally, both polymer-modified mixes demonstrated improved durability, where the 8% SBS mix exhibited the longest design life (21.66 years) and the highest number of allowable load repetitions (5.42 × 106), followed by 8% PE (13.98 years and 3.50 × 106 repetitions).
The members of the family of Eentrobacteriaceae harbour a gene cluster called polyketide synthase (pks) island. This cluster is responsible for the synthesis of the genotoxin colibactin that might have an important role in the induction of double-strand DNA breaks, leading to promote human colorectal cancer (CRC). Eleven out of the eighty eight isolates (12.5%) were pks+, distributed as 7 (8%) isolates of E. coli, 2 (2.25%) of K. pneumoniae and 2 (2.25%) of E. aerogenes. The cytotoxic effects of selected pks+ isolates (E. coli and E. aerogenes) on HeLa cells were represented by decreasing cell numbers and enlarged cell nuclei in comparison to the untreated cells. Cytological changes were observed when the infected HeLa cells culture
... Show MoreThe members of the family of Eentrobacteriaceae harbour a gene cluster called polyketide synthase (pks) island. This cluster is responsible for the synthesis of the genotoxin colibactin that might have an important role in the induction of double-strand DNA breaks, leading to promote human colorectal cancer (CRC). Eleven out of the eighty eight isolates (12.5%) were pks+, distributed as 7 (8%) isolates of E. coli, 2 (2.25%) of K. pneumoniae and 2 (2.25%) of E. aerogenes. The cytotoxic effects of selected pks+ isolates (E. coli and E. aerogenes) on HeLa cells were represented by decreasing cell numbers and enlarged cell nuclei in comparison to the untreated cells. Cyt
... Show MoreThis study includes using green or biosynthesis-friendly technology, which is effective in terms of low cost and low time and energy to prepare V2O5NPs nanoparticles from vanadium sulfate VSO4.H2O using aqueous extract of Punica Granatum at a concentration of 0.1M and with a basic medium PH= 8-12. The V2O5NPs nanoparticles were diagnosed using several techniques, such as FT-IR, UV-visible with energy gap Eg = 3.734eV, and the X-Ray diffraction XRD was calculated using the Debye Scherrer equation. It was discovered to be 34.39nm, Scanning Electron Microscope (SEM), Transmission Electron Microscopy TEM. The size, structure, and composition of synthetic V2O5
... Show MoreManganese sulfate and Punica granatum plant extract were used to create MnO2 nanoparticles, which were then characterized using techniques like Fourier transform infrared spectroscopy, ultraviolet-visible spectroscopy, atomic force microscopy, X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The crystal's size was calculated to be 30.94nm by employing the Debye Scherrer equation in X-ray diffraction. MnO2 NPs were shown to be effective in adsorbing M(II) = Co, Ni, and Cu ions, proving that all three metal ions may be removed from water in one go. Ni(II) has a higher adsorption rate throughout the board. Co, Ni, and Cu ion removal efficiencie
... Show MoreThis study is concerned with the effect of adding two kinds of ceramic materials on the mechanical properties of (Al-7%Si- 0.3%Mg) alloy, which are zirconia with particle size (20μm > P.S ≥ 0.1μm) and alumina with particle size (20μm > P.S ≥ 0.1μm) and adding them to the alloy with weight ratios (0.2, 0.4, 0.6, 0.8 and 1%). Stirring casting method has been used to make composite material by using vortex technique which is used to pull the particles to inside the melted metals and distributed them homogenously.
After that solution treatment was done to the samples at (520ºC) and artificial ageing at (170ºC) in different times, it has been noticed that the values of hardness is increased with the aging time of the o
... Show Moreليكاند ازو جديد. 4-((3-formyl-2-hydroxyphenyl)diazenyl)-N-(5-methylisoxazol-3-yl)benzenesulfonamide, الليكاند المحضر استعمل لتحضير معقدات من ايونات معادن مختلفة مثل الكروم الثلاثي والمنغنيز الثنائي والحديد الثلاثي والبلاديوم الثنائي بنسب مولية (1:1) ( ليكاند : فلز) نتائج التشخيص للمركبات يتقنيات مطيافية الاشعة فوق البنفسجية الاشعة تحت الحمراء الرنين النووي المغناطيسي البروتوني والكربوني وطيف الكتلة والتحليل الدقيق للعناصر ومحتوى الفلز وال
... Show MoreThe polymers modified Poly(vinyl chloride) differ in their tendency to photo oxidation comparing with that unmodified. It has been studied Photostability for modified Poly(vinyl chloride) chains using Schiff’s bases derivative of (5-amino-1, 3, 4-thiadiazole-2-thiol) in a manner casting of plastic chips with thickness (40) in a solvent Tetrahydrofuran. It has been determined the effectiveness Photostability of these modified polymers through the photo degradation rate constant for photostabilizer (kd) for the modified Poly (vinyl chloride). Attributed efficiency of these Poly(vinyl chloride) chips in Photostability by replace the atom Cl Poly(vinyl chloride) chains ends more stable than light stabilizer.
Metoprolol is a β1 adrenergic blocker used in treatment of heart diseases. Metoprolol (100mg) tablets was formulated as a modified release oral system utilizing the concept of bilayer system, first layer contained (30mg) as immediate release and the other (70mg) in the sustained release matrix. The immediate release layer consisted of lactose or microcrystalline cellulose as diluents with sodium starch glycolate or sodium croscarmellose as disintegrants. The result showed that the layer contains microcrystalline cellulose and 2% sodium starch glycolate gave disintegration time similar to that of conventional metoprolol tartrate tablet. This result was subjected in the subsequent preparation of the bilayer tablet. The
... Show MoreA set of hydro treating experiments are carried out on vacuum gas oil in a trickle bed reactor to study the hydrodesulfurization and hydrodenitrogenation based on two model compounds, carbazole (non-basic nitrogen compound) and acridine (basic nitrogen compound), which are added at 0–200 ppm to the tested oil, and dibenzotiophene is used as a sulfur model compound at 3,000 ppm over commercial CoMo/ Al2O3 and prepared PtMo/Al2O3. The impregnation method is used to prepare (0.5% Pt) PtMo/Al2O3. The basic sites are found to be very small, and the two catalysts exhibit good metal support interaction. In the absence of nitrogen compounds over the tested catalysts in the trickle bed reactor at temperatures of 523 to 573 K, liquid hourly space v
... Show More